54043 Mercruiser ROLLER BEARING (LOWER)


54043 ROLLER BEARING (LOWER) Mercruiser 01321017, 03301310, 6030000ES ROLLER
54043 ROLLER BEARING (LOWER) Mercruiser
Rating:
38

Buy ROLLER BEARING (LOWER) 54043 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

Mercruiser entire parts catalog list:

01321017 1987
03301310 1980,1982,1983,1984,1985,1986,1987,1988,1989,1990,1993,1994
6030000ES 1992

Information:

Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.This Special Instruction contains information on the procedure to retrofit C175 Engine CFM on the machines listed above. The wiring harnesses have been updated to supply power to the CFM sensor.Safety Section
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information.
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.Prevent possible injury by performing the procedure that follows before working on the machine.Move the machine to a smooth and level location that is away from working machines and personnel.Ground all implements.Engage the parking brake. Stop the engine.Move the hydraulic control levers to all positions to release the pressure in the hydraulic system.To avoid accidental engine starting, turn the battery disconnect switch to the OFF position. Remove the key for the battery disconnect switch. Use a secure padlock in order to lock the battery compartment access door.Place a "Do Not Operate" tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, turn the battery disconnect switch to the OFF position. Remove the key for the battery disconnect switch. Use a secure padlock in order to lock the battery compartment access door.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Before servicing/performing maintenance on the machine, electrical power must be physically disconnected; battery plugs must be disconnected from the batteries, or the trailing cable must be unplugged, and warning tags and padlocks shall be applied by a certified electrician. Certified electricians shall perform or direct any electrical work, including any energized testing, repair work in controllers, motors, or other approved compartments, and shall insure that all compartments are properly closed and inspected prior to re-energization. All applicable lock out and tag out procedures must be followed.
Personal injury or death can result from fumes, gases and ultraviolet rays from the weld arc.Welding can cause fumes, burn skin and produce ultraviolet rays.Keep your head out of the fumes. Use ventilation, exhaust at the arc, or both, to keep fumes and gases from your breathing area. Wear eye, ear and body protection before working.Protect yourself and others; read and understand this warning. Fumes and gases can be dangerous to your health. Ultraviolet rays from the weld arc can injure eyes and burn skin. Electric shock can cause death.Read and understand the manufacturer's instructions and your employer's safety practices. Do not touch live electrical parts.See "American National Standard Z49.1, Safety in Welding and Cutting" published by the American Welding Society.American Welding Society
2501 N.W. 7th Street
Miami, Florida 33125
See "OSHA Safety and Health Standards, 29 CFR 1910", available from U.S. Department of Labor.U.S. Department of Labor
Washington, D.C. 20210
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Rework Instructions for 258-6992 Fuel Filter Lines Gp with 495-2451 Fuel Filter Lines Gp
Installation Instructions for 125-9738 Block
Table 1
Required Parts
Item Qty Part Number Part Name
1 2 125-9738 Block


Parts roller Mercruiser:

35990A 1
 
35990A 1 ROLLER BEARING ASSEMBLY, PINION GEAR
00014332, 00019003, 01321017, 01326013, 03301310, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5S21800TS, 6030000ES
66818A 1
 
66818A 1 ROLLER BEARING ASSEMBLY, PINION GEAR
00019003, 01321017, 01326013, 2250507, 5000165CE, 5220200AS, 91331015
35988A 3
 
35988A 3 ROLLER BEARING ASSEMBLY, DRIVE GEAR
00019003, 01321017, 01326013, 2250507, 5000165CE, 5220200AS, 91331015
30956
 
30956 ROLLER BEARING
00014332, 00019003, 01321017, 01326013, 03301310, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5220200AS, 6030000ES, 91331015
21145
 
21145 ROLLER BEARING, GIMBAL HOUSING (UPPER)
00014332, 00019003, 01321017, 01326013, 03301310, 2140208, 2165208, 2250507, 5000165CE, 6030000ES
35246
 
35246 ROLLER BRG, DRIVE SHAFT
01321017, 03301310, 5120150AR, 5220200AS, 6030000ES, 91331015
54042T
ROLLER BEARING, BEARING CARRIER
54042T ROLLER BEARING, BEARING CARRIER
01321017, 03301310, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
68290A 1
 
68290A 1 ROLLER BRG, DRIVE SHAFT
01321017, 03301310, 5220200AS, 91331015
Back to top