811376 Mercruiser BUSHING


811376 BUSHING Mercruiser 40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND BUSHING
811376 BUSHING Mercruiser
Rating:
58

Buy BUSHING 811376 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$135.33
 

24-03-2023
0.24[0.11] Pounds
-: -
New Winderosa 811376 Complete Gasket Kit with Oil Seals Compatible with/Replacement For Husqvarna FE 350 2017-2019, KTM EXC-F 350 2017-2019
Specs: Description: Complete Gasket Kit with Oil Seals, Includes every gasket O-ring and seal required trebuild an engine., Includes formed rubber valve cover gaskets., Does not include mechanical water pump seal. || Compatible with/Replacement For: Husqvarna FE 350 2017 - 2019, KTM EXC-F 350 2017 - 2019 || 1-year warranty protects you after your purchase. We're confident that our products will work flawlessly once installed in your vehicle. But in a rare case that it does not, we'll replace it anytime within one year of your order. If you have a problem, we will take every step to assist you, contact us for a replacement. || 100% New aftermarket Complete Gasket Kit with Oil Seals built to meet OEM specifications For Husqvarna, KTM
$122.81
 

08-05-2022
0.24[0.00] Pounds
-: -
Vertex 811376 Complete Gasket Set
These sets include all gaskets and seals necessary to rebuild the engine and transmission.
Number on catalog scheme: 1
 

Mercruiser entire parts catalog list:

40280001D 1998
40420001D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C72040TD 1998
4C8204DLD 1998
4CJ2040ND 1998

Information:

Start By:a. remove flywheel
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use tool (A) to remove seal (1). 3. Install tool (C) in the flywheel housing as shown.4. Install tool (B) between tool (C) and wear sleeve (2). Turn tool (B) until the tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Rear Seal and Wear Sleeve
Serial No. 8GB1-181 1. Install adapter (3) on tooling (A) as shown.
If the crankshaft and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve as a unit must be used as a replacement.
The rear seal and wear sleeve can not be exchanged with the front seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals can cause the oil to come out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3). 3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter.
Do not put engine oil on the seal during installation. Lubrication of the seal at installation can give a false indication of leakage at a later time.
5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.6. Put clean engine oil on the O-ring seal, and install the seal on the adapter and put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over locator.11. Put clean engine oil on the face of nut (G) on the locator and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adaptor are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install flywheel Serial No. 8GB182-Up
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Use the following procedure to install the crankshaft rear seal and wear sleeve:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any Quick Cure Primer or Retaining Compound get on the lip of the seal.b. Install locator (A) and the bolts on the crankshaft.c. The seal and wear sleeve must be installed dry. Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the rear seal group for an engine is different from the front seal group. If a seal group is installed on the wrong side of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (1), as a unit, in position on locator (A). e. Put installer (C) in position on locator (A).f. Put clean engine oil on the face of nut (D) and its contact area on installer (C). Install nut (D) on locator (A).g. Tighten nut (D) until installer (C) makes contact with locator (A).h. Remove the tooling from the crankshaft.End By:a. install flywheel


Parts bushing Mercruiser:

855461
 
855461 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801333864
 
801333864 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801331712
 
801331712 BUSHING
442B110GD, 442B115KD
811377
 
811377 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801331745
 
801331745 BUSHING
442B110GD, 442B115KD
881796
BUSHING
881796 BUSHING
442B110GD, 442B115KD
801763874
 
801763874 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
854090
BUSHING
854090 BUSHING
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
Back to top