813307 Mercruiser ROLLER BEARING


813307 ROLLER BEARING Mercruiser 428B116KD, 442B110GD, 442B115KD, 4A72040ND ROLLER
813307 ROLLER BEARING Mercruiser
Rating:
13

Buy ROLLER BEARING 813307 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$31.29

24-11-2024
0.94[0.42] Pounds
US: Race-Driven Inc
CV Boot Kit for Honda Pioneer 500 SXS500 2018-2021 Front Inner and Outer
Race-Driven Heavy Duty CV Boot || High quality rubber for extended life kit includes grease and clamps. || Replace those cracked or punctured boots before dirt and water ruin your CV shaft. || Fits: 2018 2019 2020 2021 Honda Pioneer 500 SXS500M2
$38.99

24-11-2024

US: Marketplace Pros
Dumble RV Stabilizer Jacks - 2pk 1300lb Cap Attachable Telescoping Travel Trailer Jack Stabilizer Stands and Jack Rod
Dumble [Level Up Your Travel Game]: Ensure stability when loading and unloading with the Dumble RV Supplies Folding Trailer Stabilizer Jacks for Campers and more; Includes 2 flip down trailer legs and 1 handle || [Optimal Weight Capacity]: Each RV jack stand provides a lift capacity up to 650 pounds (294.8kg) and a 1,000-pound (453.6kg) breaking point; Rear trailer stands work as sport utility trailer jacks, pop up camper stabilizer jacks, RV leveling jacks, food truck drop leg trailer supports, and boat trailer drop jacks || [Expanding Height]: Telescoping stabilizer jacks can be adjusted from 12 to 18 inches (30.5 to 45.7cm) tall effortlessly by using the 11.7-inch (29.7cm) long steel jack rod handle || [Built To Last]: Premium powder-coated steel trailer leveling jacks resist outdoor elements for long-lasting reliability; Trailer jack foot plate measures 3.4 by 3.9 inches (8.6 x 9.9cm) wide for stability || [Folds Up for Safe Travels]: Mount to camper bumper, then pull down on leg to fold cargo trailer jack stands up and down; Spring mechanism and notches ensure a secure hold when driving; Swing down trailer stabilizer jacks will stand 4.1 inches (10.4cm) from mounted surface
Number on catalog scheme: 39
 

Compatible models:

Information:

3. Remove cylinder liners (1) with Tool (A).4. Remove the O-ring seals and filler band from each of the cylinder liners.Install Cylinder Liners
1. Clean cylinder liners (3) and the liner bores in the cylinder block.2. Install the cylinder liners in the block without the O-ring seals or filler bands.3. Check the cylinder liner projection as follows:a. Install the S1589 Bolts (2) and 1S379 Washers of Tool (B) on the cylinder block next to each liner. Tighten the bolts evenly, in four steps: 14 N m (10 lb ft), 35 N m (25 lb ft), 70 N m (52 lb ft) and 95 N m (70 lb ft).b. Put the adapter plate on top of the liner, and install the remainder of Tool (B). Tighten the 1D4595 Bolts (1) evenly in four steps: 7 N m (5 lb ft), 20 N m (15 lb ft), 35 N m (25 lb ft) and 70 N m (52 lb ft).c. Check to be sure the distance from the bottom edge of the crossbar to the top of the cylinder block is the same on both sides of the liner.d. Check the cylinder liner projection with Tool (C) at four locations around the liner.e. Liner projection must be 0.033 to 0.175 mm (.0013 to .0069 in). Measurements on the same liner must not be different by more than 0.05 mm (.002 in). Average measurements between liners next to each other must not be different by more than 0.05 mm (.002 in). The maximum permissible difference between average projection of all cylinder liners is 0.10 mm (.004 in). If the liner is turned in the bore, it can make a difference in the liner projection.4. If the projection is not 0.033 to 0.175 mm (.0013 to .0069 in), check the thickness of the following parts: spacer plate, spacer plate gasket and cylinder liner flange. The thickness of the spacer plate must be 9.970 0.025 mm (.3925 .0010 in). The thickness of the spacer plate gasket must be 0.208 0.025 mm (.0082 .0010 in). The thickness of the cylinder liner flange must be 10.282 0.020 mm (.4048 .0008 in). If the liner projection changes from point to point around the liner, turn the liner to a new position in the bore. If the liner projection is still not to specifications, move the liner to a different bore.5. When the cylinder projection is correct, put an alignment mark on the liner and block so the liner can be installed in the same position from which it was removed. Cylinder liner projection can be adjusted by the removal of material from (machining) the contact face of the cylinder block with the use of the 8S3140 Cylinder Block Counterboring Tool Arrangement. Machine to a minimum depth of 0.76 mm (.030 in) and to a maximum depth of 1.14 mm (.045 in). The instructions for the use of the tool group are in Special Instruction, Form No. FM055228. Shims are available for the adjustment of the liner projection. See topic, "Cylinder Liner Projection" in Testing & Adjusting Manual for the shim thickness and part number.6. Remove Tool (B) and (C). Remove the liner. 7. Put liquid soap on the bottom of the liner bore in the block, on the grooves in lower liner and on O-ring seals (4). Install the O-ring seals on the liner.8. Put filler band (5) in clean SAE 30 oil for a moment. Install it on the liner. Install the cylinder liner immediately in the cylinder block (before expansion of filler band). 9. Make sure the mark on the liner is in alignment with the mark on the block. Use Tool (A) to push the liner into position.10. Do Steps 5 through 9 for the remainder of the cylinder liners.End By:a. install pistons


Back to top