85675 BEARING UNIT, CRANKSHAFT MAIN (STANDARD) Mercruiser
01206002, 01207333, 01326013, 01402414, 01406002, 01407333
BEARING
Price: query
Rating:
Mercruiser entire parts catalog list:
01207333 1983
- CYLINDER BLOCK, PISTON AND BEARINGS (140-3.0L-181 CID) » 85675
- CYLINDER BLOCK, PISTON AND BEARINGS (120-2.5L-135 CID) » 85675
- CYLINDER BLOCK, PISTON AND BEARINGS » 85675
01402414 1984,1985,1986,1987,1988,1989
- CYLINDER BLOCK, PISTON AND BEARINGS (140-3.0L-181 CID) » 85675
- CYLINDER BLOCK, PISTON AND BEARINGS (120-2.5L-135 CID) » 85675
01407333 1983
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods and injector sleeves in the cylinder head to prevent the entry of loose parts into the engine.
Rotate the crankshaft to position the piston of the cylinder that is being worked on in the top dead center position.
Illustration 1 g06361900
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Step 2a through Step 2d to position the appropriate piston at top dead center.
Install Tooling (A) in position on the cylinder head to compress a valve spring (10) for the appropriate piston.
Use Tooling (A) to compress valve spring (10) and open the valve slightly.Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11).
Use Tooling (B) to rotate the crankshaft carefully, until the piston touches the valve.Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed.Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (A) to allow removal of valve keepers (1).Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).Remove valve keepers (1).
Slowly release pressure on Tooling (A).
Remove valve spring retainer (2) and remove valve spring (10).
If necessary, remove valve stem seals (4).
Repeat Step 3 through Step 6 to remove the remaining valve springs from the appropriate cylinder.
Remove Tooling (A).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B
Parts bearing Mercruiser:
34469
34469 BEARING, CAMSHAFT THRUST
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
32538
32538 BEARING, ROLLER - GIMBAL RING
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE
85701
85701 BEARING SET (PAIR), CONNECTING ROD (STANDARD)
00014332, 01207333, 01402414, 01406002, 01407333, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 411102KN2, 430B00001, 430L000JS, 43320
85702
85702 BEARING UNIT (PAIR), CONNECTING ROD (.001 U.S.)
00014332, 01207333, 01402414, 01406002, 01407333, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 411102KN2, 430B00001, 430L000JS, 43320
85719
85719 BEARING UNIT, CRANKSHAFT MAIN - REAR (.020 U.S.)
01206002, 01207333, 01326013, 01402414, 01406002, 01407333
85677
803090T 1
92366A 1