85676 Mercruiser BEARING UNIT, CRANKSHAFT MAIN (.001 U.S.)


85676 BEARING UNIT, CRANKSHAFT MAIN (.001 U.S.) Mercruiser 01206002, 01207333, 01326013, 01402414, 01406002, 01407333 BEARING
85676 BEARING UNIT, CRANKSHAFT MAIN (.001 U.S.) Mercruiser
Rating:
73

Buy BEARING UNIT, CRANKSHAFT MAIN (.001 U.S.) 85676 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Compatible models:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the bottom mating surface of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves to identify the correct position.Note: Inlet valves have a recess in the center of the head.
Use a suitable lifting device to position the cylinder head with the valve springs upward. The weight of the cylinder head is approximately 50 kg (110 lb).Note: Ensure that the cylinder head is kept on a clean, soft surface to prevent damage to the machined face.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g06361900
Install Tooling (A) in position on the cylinder head to compress appropriate valve spring (3).
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply sufficient pressure to Tooling (A) to remove valve keepers (1).Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).
Slowly release pressure on Tooling (A).
Illustration 2 g06362258
Place a temporary identification mark on valve spring (3) to identify the correct position.
Remove valve spring retainer (2). Remove valve spring (3).
Repeat Step 4 through Step 8 for the remaining valves.
Remove Tooling (A).
Remove valve stem seals (4).
Use a suitable lifting device to carefullyturn over the cylinder head.
Remove valves (5).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The valves have a hard surface finish. Grinding compound must not be used on the valves. Grinding compound will damage the hard surface finish of the valves.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Step 1a through Step 1e to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to System Operation, Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure.
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect valve springs (3) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves" for further information.
Illustration 3 g06362258
Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate positions in the cylinder head. Check the depth of the valves below the face of the cylinder head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
Use a suitable lifting device to carefully turn over the cylinder head. The weight of the cylinder head is approximately 50 kg (110 lb).Note: Ensure that all the valves remain in place.
Install new valve stem seals (4) onto each of the valve guides.Note: The outer face of the valve guides must be clean before installing valve stem seals (4).
Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) on valve spring (3).


Parts bearing Mercruiser:

34469
 
34469 BEARING, CAMSHAFT THRUST
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
32538
 
32538 BEARING, ROLLER - GIMBAL RING
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE
85701
 
85701 BEARING SET (PAIR), CONNECTING ROD (STANDARD)
00014332, 01207333, 01402414, 01406002, 01407333, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 411102KN2, 430B00001, 430L000JS, 43320
85702
 
85702 BEARING UNIT (PAIR), CONNECTING ROD (.001 U.S.)
00014332, 01207333, 01402414, 01406002, 01407333, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 411102KN2, 430B00001, 430L000JS, 43320
85719
 
85719 BEARING UNIT, CRANKSHAFT MAIN - REAR (.020 U.S.)
01206002, 01207333, 01326013, 01402414, 01406002, 01407333
85677
 
85677 BEARING (PAIR), CONNECTING ROD (STANDARD)
01206002, 01207333, 01326013, 01402414, 01407333
803090T 1
 
803090T 1 BEARING AND SEAL KIT
00019003, 01321017, 01326013, 5000165CE
92366A 1
 
92366A 1 BEARING ASSEMBLY, Roller, DRIVE SHAFT
00019003, 01321017, 01326013, 5000165CE
Back to top