896332074 Mercruiser BOLT


896332074 BOLT Mercruiser 40280001D, 4C72040TD BOLT
896332074 BOLT Mercruiser
Rating:
18

Buy BOLT 896332074 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Compatible models:

40280001D   4C72040TD   Mercruiser

Mercruiser entire parts catalog list:

Information:


Table 1
Module Identifiers    
MID    Description    
30     Caterpillar Monitoring System    
36     Engine ECM    
74     Payload Control System    
81     Transmission ECM    
82     Electronic Implement Control    
122     Product Link    
124     Theft Deterrent System    Component Identifier (CID) - The CID is a number with three or four digits. The CID indicates the component that generated the code. For example, the CID number 17 identifies the fuel shutoff valve.Failure Mode Identifier (FMI) - The FMI is a two digit code that indicates the type of failure. Table 2 is a list of the failure mode identifiers.
Table 2
Failure Mode Identifiers    
FMI    Description    
00     The data is valid, but the data is above the normal range of operation.    
01     The data is valid, but the data is below the normal range of operation.    
02     The data is erratic, intermittent, or incorrect.    
03     The voltage is above normal or shorted high.    
04     The voltage is below normal or shorted low.    
05     The current is below normal or the circuit is open.    
06     The current is above normal or the circuit is grounded.    
07     The mechanical system is not responding correctly.    
08     There is a frequency, a pulse width, or a period that is abnormal.    
09     There has been an abnormal update.    
10     There has been an abnormal rate of change.    
11     The failure mode is not identifiable.    
12     The device or the component is faulty.    
13     The device or the component is out of calibration.    
14-31     Reserved    Note: Do not confuse diagnostic codes with event codes. For information on event codes, refer to Troubleshooting, "Event Codes".Active Diagnostic Codes
An active diagnostic code represents a problem with the electronic control system. Correct the problem as soon as possible.When an active diagnostic code is generated, a warning may be displayed on an electronic display such as the Caterpillar Monitoring System.Logged Diagnostic Codes
When the ECM generates a diagnostic code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when a code is generated:
Hour of the first occurrence of the code
Hour of the last occurrence of the code
Number of occurrences of the codeThis information is a valuable indicator for troubleshooting intermittent problems. Any logged diagnostic codes will automatically be deleted if no additional occurrences are recorded in 100 hours. Some diagnostic codes may be easily triggered. Some diagnostic codes may log occurrences that did not result in complaints. The most likely cause of an intermittent problem is a faulty connection or damaged wiring. The next likely cause is a component failure. The least likely cause is the failure of the ECM. Diagnostic codes that are logged repeatedly may indicate a problem that needs special investigation.If the symptoms continue, use the proper procedure for troubleshooting the symptoms that have been experienced by the operator.Note: Always clear logged diagnostic codes after investigating and correcting the problem which generated the code.


Parts bolt Mercruiser:

896332195
 
896332195 BOLT
40280001D, 4C72040TD
896332196
 
896332196 BOLT
40280001D
889861
 
889861 BOLT
40280001D, 40280002D, 40420002D, 4C72040TD, 4CJ2040ND
896332069
 
896332069 BOLT
40280001D, 4C72040TD
896332086
 
896332086 BOLT
40280001D
896332002
896332184
 
896332184 BOLT
40280001D, 4C72040TD
896332118
 
896332118 BOLT
40280001D, 4C72040TD
Back to top