78389 Mercruiser BRACKET, CONNECTOR ATTACHING


78389 BRACKET, CONNECTOR ATTACHING Mercruiser 01206002, 01207333, 01326013, 01406002, 01407333, 08986342 BRACKET
78389 BRACKET, CONNECTOR ATTACHING Mercruiser
Rating:
73

Buy BRACKET, CONNECTOR ATTACHING 78389 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: --
 

Compatible models:

Mercruiser entire parts catalog list:

01206002 1982,1983
01207333 1983
01326013 1983
01406002 1982
01407333 1983
08986342 1982,1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7573 Link Bracket 2
D -(1) Loctite 5127 -
(1) EAME
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Engine News, 27, March 2006, "Sealing and Installing the Flywheel Housing" for more information.
Ensure that the mating surface of the flywheel housing and the engine block is clean. Both mating surfaces must be clean, dry, and free of any oil before Tooling (D) is applied.
Illustration 1 g01258819
Apply a 6.0 mm (0.25 inch) bead of Tooling (D) to the mating surface of the flywheel housing. Refer to Illustration 1.
Illustration 2 g00588658
Typical example
Use Tooling (B) and a suitable lifting device to the top of flywheel housing (2). The weight of flywheel housing (2) is approximately 210 kg (460 lb).
Position flywheel housing (2) on the engine.
If the dowel pins were removed from flywheel housing (2), install the dowel pins and ensure that the dowel pins are properly seated.
Illustration 3 g01259294
(U) 1/2 - NC
(V) 1/2 - NC
(W) 1/2 - NC
(X) 1/2 - NC
(Y) 1/2 - NC
(Z) 5/8 - NC
Install the bolts and the hard washers for flywheel housing (2). Refer to Illustration 3 for the proper locations of the bolts. Tighten the 1/2 - NC bolts to a torque of 135 20 N m (100 15 lb ft). Tighten the 5/8 - NC bolts to a torque of 270 40 N m (200 30 lb ft).
Remove Tooling (B).
Install the crankshaft rear seal and the wear sleeve.
Place the camshaft timing pins in position. Place the timing bolt in the flywheel with the No. 1 piston at the top center position on the compression stroke.
Illustration 4 g00588655
Illustration 5 g00588654
Use the following procedure to install camshaft drive gears (4).
Clean the taper of the camshaft and the tapered bore of the camshaft gear with a lint free cloth saturated with solvent to remove oil. Clean the parts again with a lint free alcohol wipe to remove any residue. The alcohol wipe is dirty after cleaning the parts. Clean the parts again with a lint free alcohol wipe until no residue is left on the alcohol wipe.Note: The taper of the camshaft and the tapered bore of the camshaft gear must be clean, dry, and free of residue before assembly.
Ensure that the camshaft timing pins and the timing pin for the flywheel are installed.
Place camshaft drive gears (4) in position. Remove the backlash by rotating the gears in the opposite direction of camshaft rotation.Note: For "Standard Rotation" engines, turn the camshaft drive gears COUNTERCLOCKWISE. For "Reverse Rotation" engines, turn the camshaft drive gears CLOCKWISE.
Install the bolt and plate (5).
Install the bolt and timing ring (3). Ensure that the hole in the timing ring is properly seated on the locating pin.
Tighten the bolt to a torque of 360 N m (265 lb ft).
Place a Mark on the bolt.
Place a driver against the retaining plate of the camshaft gear. Strike the driver solidly with a hammer 3 to 4 times.
Tighten the bolt again to a torque of 360 N m (265 lb ft).
Repeat Steps 10h and 10i until the Mark has turned at least 90 degrees.
Remove the timing pins from the camshafts and the flywheel.
Illustration 6 g00588653
Typical example
Install the gaskets and camshaft covers (1) on flywheel housing (2).
Install the engine speed/timing sensor. Refer to Testing and Adjusting, "Engine Speed/Timing Sensor".End By:
Install the engine oil pan.
If the exhaust elbow was attached to the flywheel housing, install the bracket and the exhaust elbow.
Install the rocker shaft and the pushrods.
Install the starting motors.
Install the flywheel.


Parts bracket Mercruiser:

94279
 
94279 BRACKET, MOUNTING - STARTER SOLENOID
00019003, 01321017, 01326013, 03301310, 5000165CE
47488
 
47488 BRACKET, WATER PUMP
02287333, 02607333, 08986342, 228801, 260801
77440
 
77440 BRACKET, MOUNTING-HARNESS AND CIRCUIT BREAKER
02287333, 02607333, 08986342, 228801, 260801
74633A 1
 
74633A 1 BRACKET, MOUNTING (PORT)
02287333, 08986342, 228801
2730
 
2730 BRACKET, CONDENSER
01206002, 01207333, 01326013, 01406002, 01407333, 08986342
86924
 
86924 BRACKET, CIRCUIT BREAKER
01206002, 01207333, 01326013, 01406002, 01407333
Back to top