854023 Mercruiser BRACKET-SUPPORT


854023 BRACKET-SUPPORT Mercruiser 40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD BRACKET
854023 BRACKET-SUPPORT Mercruiser
Rating:
33

Buy BRACKET-SUPPORT 854023 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$37.00
 

15-09-2023

-: -
Engine Cylinder Head Bolt Set Pioneer 854023
Manufacturer Part Number: 854023 || Warranty: 90 Day || Brand: Pioneer || Quantity: 1
$42.95
 

28-07-2022

-: -
Genuine Zippo Lighter 854023 Indian w/Turquoise
Brushed Brass Finish || Standard size || Wind resistant || Lifetime warranty
£4.47
 

07-10-2017

SBS Deutsc: SBS Deutschland GmbH
NK 854023 Brake Hose
Number on catalog scheme: 15
 

Compatible models:

Mercruiser entire parts catalog list:

40420001D 1998
428B116KD 1997,1998
442B115KD 1997
4A72040ND 1998
4C8204DLD 1998

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
1180-3
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Above Normal 3908-3
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-4
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Below Normal 3908-4
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-8
Engine Turbocharger 1 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3908-8
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-3
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Above Normal 3909-3
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-4
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Below Normal 3909-4
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-8
Engine Turbocharger 2 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3909-8
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
Illustration 1 g06323402
Schematic of the PWM sensors for the sensor signal circuit
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active or logged.
Proceed to Test Step 2.
Result: A -4 code is active or logged.
Proceed to Test Step 3.
Result: A -8 code is active or logged.
Proceed to Test Step 5.
2. Create a Short at the Sensor Connector
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Pin 2 (sensor return) and Pin 3 (sensor signal)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Remove electrical power from the engine.
Create a Short
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -4 code did not become active.
Proceed to Test Step 4.
3. Create an Open at the Sensor Connector
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
E. Remove electrical power from the engine.
Create an Open
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -3 code did not become active.
Proceed to Test Step 4.
4. Check the 8 VDC Supply Voltage at the Sensor Connector
A. Apply electrical power to the engine.
B. Measure the voltage at the following pin locations of the affected sensor connector:
- Pin 1 and Pin 2
C. Reconnect the sensor.
Supply Voltage
Result: The supply voltage is approximately 8.0 0.2 VDC
Proceed to Test Step 8.
Result: The supply voltage is not approximately 8.0 0.2 VDC.
Repair: There is a short in the wiring harness to the battery. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 5.
5. Check the PWM Circuit for an Open
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector


Parts bracket Mercruiser:

806979T
BRACKET
806979T BRACKET
442B110GD, 442B115KD, 4C72040TD, 4CJ2040ND
816340
BRACKET
816340 BRACKET
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
806238
BRACKET
806238 BRACKET
40280001D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 473B1F0GS, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4V71222PD, 4V71222TD
814158T
 
814158T BRACKET
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
879716
 
879716 BRACKET-ALTERNATOR
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD
854025
BRACKET-CONTROL UNIT
854025 BRACKET-CONTROL UNIT
428B116KD, 442B115KD, 4A72040ND, 4CJ2040ND
854026
BRACKET-REMOTE CONTROL CABLE
854026 BRACKET-REMOTE CONTROL CABLE
428B116KD, 442B115KD, 4A72040ND, 4CJ2040ND
884002
BRACKET-HEAT EXCHANGER SUPPORT
884002 BRACKET-HEAT EXCHANGER SUPPORT
428B116KD, 442B115KD, 4A72040ND
Back to top