854034 Mercruiser BRACKET-UPPER CONTROL UNIT


854034 BRACKET-UPPER CONTROL UNIT Mercruiser 428B116KD, 442B115KD, 4A72040ND, 4CJ2040ND BRACKET
854034 BRACKET-UPPER CONTROL UNIT Mercruiser
Rating:
78

Buy BRACKET-UPPER CONTROL UNIT 854034 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$129.99
 

16-09-2024

US: PremiumpartsWhosale
A-Premium Front Windshield Wiper Motor and Linkage Assembly Compatible with Honda Vehicles - Civic 2008 2009 2010 2011, Sedan - Replace# 76505-SNA-A01, 76530-SNA-A11
A-Premium [Vehicle Fitment]: Compatible with Honda Civic 2008-2011 Sedan---with Wiper Linkage & Motor; Without Washer Pump || [Reference Number]: 76505-SNA-A01, 76505-SNA-A02, 43-4034, 85-4034, 76530-SNA-A11, 76530-SNA-A03, 602-961---Please enter your vehicle information in the top left corner of listing and check our "Special Note" before ordering || [Package Content]: 1x Windshield Wiper Motor and Linkage Assembly (Included: Wiper Motor + Wiper Linkage); Packaging Type: Box || [Function]: OE replacement A-Premium Front Windshield Wiper Transmission Linkage with Motor Assembly. Taking the delicate technology design to match all specifications of the original parts. Reliable construction for splendid performance. Simple installation and easy operation will save much of your time || [Buy with Confidence]: A-Premium offers a one-year unlimited-mileage guarantee on our meticulously crafted wiper motor and linkage assembly. We offer a wide variety of automotive accessory categories, ensuring that you can hit the road with peace of mind.
$46.99
 

16-09-2024

US: PremiumpartsWhosale
A-Premium Front Windshield Wiper Motor Compatible with Honda Civic 2006 2007 2008 2009 2010 2011, Sedan, 5-Pin, Replace# 76505-SNA-A01, 76505-SNA-A02
A-Premium [Vehicle Fitment]: Compatible with Honda Civic 2006-2011 l4 1.3L, 2006-2011 l4 1.8L, 2007-2011 l4 2.0L---Sedan || [Reference Number]: 43-4034, 434034, 85-4034, 854034, 76505-SNA-A01, 76505SNA-A01, 76505-SNA-A02, 76505SNAA02---Please enter your vehicle information in the top left corner of listing and check our "Special Note" before ordering || [Note]: Location: Front Side; It comes Without Washer Pump; with 5-Pin Connector || [Function]: OE replacement A-Premium Windshield Wiper Motor. Taking the delicate technology design to match all specifications of the original parts. So that it can effectively control the motor speed and then control the scraping arm speed || [Buy with Confidence]: A-Premium offers a one-year unlimited-mileage guarantee on our meticulously crafted wiper motor. We offer a wide variety of automotive accessory categories, ensuring that you can hit the road with peace of mind.
$59.53
 

25-09-2020

-: -
Dts New Windshield Wiper Motor for Honda Civic Hybrid Sedan 2.0L - WPM4034
100% New aftermarket unit built to meet OEM specifications || NEW units are manufactured under the guidelines of ISO Quality Standards to ensure consistent quality || 434034 PPWPM4034 WPM4034 246347 76505SNAA01 854034 || 76505SNAA02 43-1148
Number on catalog scheme: 10
 

Compatible models:

Mercruiser entire parts catalog list:

428B116KD 1997,1998
442B115KD 1997
4A72040ND 1998
4CJ2040ND 1998

Information:

If a fault occurs with the primary throttle with secondary throttle is installed, the secondary throttle will be used until the fault is repaired.If a fault occurs with the secondary throttle, the engine will use the primary throttle until the fault is repaired.If a functional throttle is not available, the following conditions will occur:
The engine will default to the limp home speed.
If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.
If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.
The engine will remain at this speed while the diagnostic code remains active.
All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.
All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been cycled.The diagnostic codes above relate to an analog sensor. Use this procedure only if the analog sensor uses an output from a variable resistor.The sensor is most likely to be mounted on a throttle pedal. The sensor is attached directly to the throttle assembly. The sensor provides an output voltage to the ECM. The sensor output voltage will vary with the position of the throttle. Foot operated or hand operated throttle assemblies are available.The sensor receives +5 VDC power from the ECM. The sensor will produce a raw signal voltage that will alter between low idle and high idle. The voltage is changed into a throttle position within the range 0% to 100% by the ECM.The sensor senses the speed requirement from the throttle position. A second sensor may override this speed requirement from the first sensor. This override will be subject to an input from a secondary throttle or from the SAE J1939 (CAN) data link or from a PTO control.Use the electronic service tool in order to check the input status.Note: The identification letters for the terminals in the connectors may vary dependent on the manufacturer of the throttle pedal.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 ECM connector and the analog throttle position sensors.
Refer to Troubleshooting, "Electrical Connector - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the analog throttle position sensor connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the analog throttle position sensors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the


Parts bracket Mercruiser:

806979T
BRACKET
806979T BRACKET
442B110GD, 442B115KD, 4C72040TD, 4CJ2040ND
816340
BRACKET
816340 BRACKET
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
806238
BRACKET
806238 BRACKET
40280001D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 473B1F0GS, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4V71222PD, 4V71222TD
884002
BRACKET-HEAT EXCHANGER SUPPORT
884002 BRACKET-HEAT EXCHANGER SUPPORT
428B116KD, 442B115KD, 4A72040ND
889887
BRACKET, Injector Nozzle Hold Down
889887 BRACKET, Injector Nozzle Hold Down
40280001D, 4C72040TD, 4CJ2040ND
889922
BRACKET
889922 BRACKET
4C72040TD, 4CJ2040ND
889895
BRACKET
889895 BRACKET
4C72040TD, 4CJ2040ND
889917
Back to top