862226A 2 Mercruiser BRACKET, Drain


862226A 2 BRACKET, Drain Mercruiser 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2 BRACKET
862226A 2 BRACKET, Drain Mercruiser
Rating:
53

Buy BRACKET, Drain 862226A 2 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mercruiser entire parts catalog list:

4111021L1 1998
4111021TS 1998
4111021UT 1998
4111021UU 1998
411102KN2 1998

Information:


Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledgeMechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).MEUI A Injector Adjustment
Table 1
Required Tools
Part Number Part Name Quantity
9U-7227 Injector Height Gauge 1
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height GaugeTo adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Injector height gauge (4) is used to obtain a dimension of 78.0 0.2 mm (3.07 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body.
Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body.
Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body.
Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 10 N m (74 7 lb ft).
To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke.
Repeat Steps 3 through 4.
Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.MEUI C Injector Overview
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connectorMechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).MEUI C Injector Adjustment
Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Set injectors 3, 5, and 6 using the procedure that follows.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).


Parts bracket Mercruiser:

65606T
BRACKET, MOUNTING
65606T BRACKET, MOUNTING
01207333, 01402414, 01407333, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 430B00001, 430L000JS
811868
BRACKET ASSEMBLY, Front
811868 BRACKET ASSEMBLY, Front
02602347, 02608427, 257B021JS, 4111021L1, 411102KN2, 4211015L1, 430B00001, 430L000JS, 4350100KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 44541101S, 4454110GE, 4454110JT, 45021102S, 457B100KS, 4M11025LS
811874
BRACKET ASSEMBLY, Rear
811874 BRACKET ASSEMBLY, Rear
02602347, 02608427, 257B021JS, 4111021L1, 430B00001, 430L000JS, 4350100KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 44541101S, 4454110GE, 4454110JT, 45021102S, 457B100KS
61897T
BRACKET, Rear Upper
61897T BRACKET, Rear Upper
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430L000JS
807213A 1
 
807213A 1 BRACKET, Starter
4111021L1, 430L000JS
811874T
 
811874T BRACKET ASSEMBLY, Rear
4111021L1, 411102KN2, 4211015L1, 4M11025LS
861734
 
861734 BRACKET, Alternator
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE
807962A14
 
807962A14 BRACKET ASSEMBLY, Shift
4111021L1, 4111021TS, 411102KN2, 4211025RS, 4211025TS, 4211025TT, 424106LRS, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M4102LRS, 4M4102LTS, 4S42028N1
Back to top