863178 BRACKET, Steering Sensor Mercruiser
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
BRACKET
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Mercruiser entire parts catalog list:
- SMARTCRAFT SENSORS AND HARNESSES » 863178
- SMART CRAFT SENSOR AND HARNESSES » 863178
- SMART CRAFT SENSOR AND HARNESSES » 863178
- SMARTCRAFT SENSOR AND HARNESSES » 863178
- SMARTCRAFT SENSOR AND HARNESSES » 863178
- SMARTCRAFT SENSOR AND HARNESSES » 863178
- SMARTCRAFT SENSOR AND HARNESSES » 863178
Information:
Illustration 1 g01728067
Electronic unit injector
Test Step 1. Check for Diagnostic Codes that are Related to this Procedure
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position.
Check for logged diagnostic codes that are related to this procedure.
Make a note of the logged diagnostic codes. Expected Result:Expected Result 1One or more of the following diagnostic codes are logged:
1-2 Cylinder #1 Injector erratic, intermittent, or incorrect
2-2 Cylinder #2 Injector erratic, intermittent, or incorrect
3-2 Cylinder #3 Injector erratic, intermittent, or incorrect
4-2 Cylinder #4 Injector erratic, intermittent, or incorrect
5-2 Cylinder #5 Injector erratic, intermittent, or incorrect
6-2 Cylinder #6 Injector erratic, intermittent, or incorrect Expected Result 2Injectors 1, 2 and 3 share a common injector driver circuit in the ECM. Injectors 4, 5 and 6 share a common driver circuit in the ECM. If three injectors that share a common supply indicate a diagnostic code then this is probably caused by a faulty ECM.Results:
OK - Result 1 One or more diagnostic codes are logged. Proceed to Test Step 2.
OK - Result 2 Three injectors that share a common supply indicate a diagnostic code. Proceed to Test Step 3.
Not OK - No related diagnostic codes are logged.STOPTest Step 2. Check the Faulty Cylinder Numbers
Use the electronic service tool in order to make a note of the logged diagnostic codes.
Use the noted diagnostic codes in order to check the cylinders for faulty injectors. Expected Result:The diagnostic codes indicate the cylinder numbers that have faulty injectors.Results:
OK - No related diagnostic codes are logged.STOP
Not OK - The diagnostic codes indicate the cylinder numbers that have faulty injectors.Repair: Replace the faulty injectors.Use the electronic service tool in order to program the replacement trim files for the injectors. Refer to Troubleshooting, "Injector Trim File" for further information.Use the electronic service tool in order to clear the logged codes.Turn the keyswitch to the ON position.Start the engine.Use the electronic service tool in order to perform the "Fuel System Verification Test". If the cylinders indicate "PASS", then the fault has been cleared.Verify that the repair eliminates the fault.STOPTest Step 3. Check the ECM
Make sure that the latest flash file for the application is installed in the ECM. Refer to Troubleshooting, "Flash Programming".
Contact the technical communicator at the Caterpillar dealer. Note: This consultation can greatly reduce the repair time.
If the technical communicator recommends the use of a test ECM, install a test ECM. Refer to Troubleshooting, "Replacing the ECM".
Use the electronic service tool in order to perform the "Fuel System Verification Test". Verify that the test eliminates the fault. Note: The "Fuel System Verification Test" will indicate if the cylinder has a "Pass" or "Fail". If the cylinders indicate "Pass" then the fault has been cleared.
If the test ECM eliminates the fault, reconnect the suspect ECM.
Use the electronic service tool in order to perform the "Fuel System Verification Test". Expected Result:The test ECM clears the fault. The "Fuel System Verification Test" with the suspect ECM indicates a "FAIL" condition.Results:
OK - The test ECM eliminates the fault and the suspect ECM indicates a "FAIL" condition. Replace the faulty ECM. Verify that the repair eliminates the fault.STOP
Not OK - The test ECM did not eliminate the fault.Repair: Reinstall the original ECM.Repeat the test procedure from Step1.
Parts bracket Mercruiser:
807979T
807979T BRACKET
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4262C01JT, 4332087N1, 4350104KS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 4454118JT, 4542067LS, 457B101KS, 4652027LE, 4652027M
879194T
879172T31
879194T49
864468T
862986
862342T
865638T