864447 Mercruiser BRACKET, Fuel Filter Brace


864447 BRACKET, Fuel Filter Brace Mercruiser 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS BRACKET
864447 BRACKET, Fuel Filter Brace Mercruiser
Rating:
78

Buy BRACKET, Fuel Filter Brace 864447 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$14.99
 

23-08-2021
0.28219169536[0.00] Pound
-: -
New Mercury Mercruiser Quicksilver OEM Part # 864447 BRACKET-BASE
Number on catalog scheme: 25
 

Compatible models:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7M-3978(1) Piston Ring Expander Gp 1
7B-7974(2) Piston Ring Expander Gp 1
C 5P-8639 Hydraulic Press (Connecting Rod Bearing) 1
8F-0024 Hose Assembly 1
1P-2375 Connecting Coupler 1
1P-2376 Connecting Coupler 1
5P-8651 Spacer 1
5P-8649 Adapter 1
5P-8650 Bushing Adapter 1
9U-6600 Hand Hydraulic Pump 1
(1) For use with 137 mm (5.4 inch) bores.
(2) For use with 145 mm (5.7 inch) bores.Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01017742
Illustration 2 g01018268
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Raise heat of connecting rod (6) along Length (Y). (Y) Maximum Length for heating the connecting rod ... 95 mm (3.7 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use Tooling (C) to remove the old bearing and install new bearing (7) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (6). Note: Orient the bearing joint within 5 degrees of either Location (X).
Use a pin boring machine to machine the bore of bearing (7) to the correct diameter. Diameter of bearing bore ... 60.035 0.008 mm (2.3636 0.0003 inch)
Illustration 3 g01056145
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (8) and install the connecting rod pin. Install pin retainer (5) with Tooling (A).
Install upper connecting rod bearing (9) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (10) in connecting rod bearing cap (11). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts bracket Mercruiser:

807979T
BRACKET
807979T BRACKET
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4262C01JT, 4332087N1, 4350104KS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 4454118JT, 4542067LS, 457B101KS, 4652027LE, 4652027M
863451T
BRACKET, Water Drain Actuator
863451T BRACKET, Water Drain Actuator
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
863211T01
BRACKET, Alternator Mounting
863211T01 BRACKET, Alternator Mounting
40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M4102LRS, 4M4102LTS
865188T01
BRACKET
865188T01 BRACKET
40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M11025US, 4M4102LRS, 4M4102LTS
861714T
BRACKET, ECU Mounting
861714T BRACKET, ECU Mounting
4231017L1, 4332087N1, 4441027LE, 444106LPS, 4652027M1, 4652227MW, 4M31027LS, 4R42027N1
864494T
BRACKET, Cooler
864494T BRACKET, Cooler
40500006T, 40500010T, 40500010U, 40500120U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M4102LRS, 4M4102LTS
865188T
BRACKET
865188T BRACKET
40500006T, 40500010T, 40500010U, 40500120U, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M4102LRS, 4M4102LTS
864484
BRACKET
864484 BRACKET
444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS
Back to top