864456T BRACKET, Alternator Brace Mercruiser
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
BRACKET
Price: query
Rating:
Compatible models:
Mercruiser entire parts catalog list:
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
- ALTERNATOR AND BRACKETS » 864456T
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
C - Red Rubber Grease -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores, the coolant passages, and the lubricant passages.Note: Thoroughly clean the hole in the cylinder head for the gas that is ventilated from the crankcase. Ensure that the hole is not restricted by debris and/or oil deposits.
Illustration 1 g00951564
Install the cylinder head gasket on the dowels (10) on top of the cylinder block. Note: Do not use any sealant or compound on the cylinder head gasket.
Install the Tooling (A) in the cylinder block.
Use a suitable lifting device to install the cylinder head. The weight of the cylinder head is approximately 57 kg (126 lb). Note: Ensure that the cylinder head is positioned on dowels (10). Take care not to damage the machined surfaces of the cylinder head during installation.
Remove the Tooling (A).
Illustration 2 g00951563
Clean the threads of the setscrews that secure the cylinder head. Inspect the threads of the setscrews that secure the cylinder head. Note: Do not use the setscrews if there is any visual reduction in the diameter of the threads (Y) that has not been engaged with the cylinder block. Use a straight edge to check the bolts.
Apply clean engine oil to the threads and the shoulder of the setscrews that secure the cylinder head before installation.
Illustration 3 g00951484
Install the setscrews (8) in cylinder head (9). Note: The short setscrews are installed in holes that are marked 2, 5, 6, 7, 8, 9, and 10.Note: The long setscrews are installed in holes that are marked 1, 3, and 4.
Tighten the setscrews in numerical order to a torque of 50 N m (37 lb ft). Refer to Illustration 3.
Tighten the setscrews in numerical order to a torque of 100 N m (74 lb ft). Refer to Illustration 3.
Illustration 4 g01151296
Use the Tooling (B) to achieve the correct final torque. Note: If the Tooling (B) is not available, place an index mark on each setscrew.
Tighten the setscrews in numerical order. Refer to Illustration 3.
Turn the short setscrews (2, 5, 6, 7, 8, 9, and 10) for an additional 225 degrees.
Turn the long setscrews (1, 3, and 4) for an additional 270 degrees.
Illustration 5 g00954953
Install new O-ring seals on the bypass tube (7). Apply Tooling (C) to the O-ring seals. Install the bypass tube in the cylinder head. Install the setscrews (6).
Illustration 6 g00951472
Connect the tube assembly (5) to the cylinder head.
Connect the harness assembly (4) to the coolant temperature sensor.
Install bolt (1) and the fuel line to the cylinder head.
Fill the cooling system with coolant. Fill the lubrication system with engine oil. Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the cooling system capacity and the lubrication system capacity of the engine.End By:
Install the glow plugs. Refer to Disassembly and Assembly Manual, "Glow Plugs - Remove and Install".
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the fuel injection Nozzles. Refer to Disassembly and Assembly Manual, "Fuel Injection Nozzles - Install".
Install the pipe for the boost control.
Install the fuel priming pump. Refer to Disassembly and Assembly Manual, "Fuel Priming Pump and Fuel Filter Base - Remove and Install".
Install the hose from the integral air inlet to the air filter. Refer to the OEM information for further details.
Refill the engine with coolant and engine oil. Refer to the Operation and Maintenance Manual for the correct procedure, the quantities, the coolant specification, and the specification for the engine oil.
Parts bracket Mercruiser:
8M2004597
818598T
818598T BRACKET, Shift Plate Mounting
40430002S, 4231017L1, 4332087N1, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 4652027LE, 4652027M1, 4652227MW, 4M11025LS, 4M31027LS, 4M4102LPS, 4R42027N1
863211T01
863211T01 BRACKET, Alternator Mounting
40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M4102LRS, 4M4102LTS
863714T01
863714T01 BRACKET
40500006T, 40500010T, 40500010U, 4211025TT, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 4M11025TT, 4M11025US
863715T01
863715T01 BRACKET
40500006T, 40500010T, 40500010U, 4211025TT, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M4102LRS, 4M4102LTS
861714T
861714T BRACKET, ECU Mounting
4231017L1, 4332087N1, 4441027LE, 444106LPS, 4652027M1, 4652227MW, 4M31027LS, 4R42027N1
863663T
879194T03