897345006 Mercruiser BRACKET


897345006 BRACKET Mercruiser 40200002D, 40200002G BRACKET
897345006 BRACKET Mercruiser
Rating:
43

Buy BRACKET 897345006 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$154.66
 

07-10-2017
2.69[0.90] pounds
Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 897345006 Bracket
Number on catalog scheme: 15
 

Compatible models:

40200002D   40200002G   Mercruiser

Mercruiser entire parts catalog list:

40200002D 1998
40200002G 1998

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     132-5451     Holding Fixture     1    
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Drain the cooling system into a suitable container for storage or disposal. Refer to Disassembly and Assembly, "Cooling System Coolant - Change".
Loosen the purge valves, and release the air pressure in the air tank.
Illustration 1 g00620850
Typical example
Disconnect coolant tube assembly (1) and air hose assembly (2) from the air compressor.
Disconnect oil tube assembly (3) from the air compressor.
Illustration 2 g00928842
Typical example
Remove coolant hose assembly (4) from the air compressor.
Remove nuts (5) that hold the air compressor to the accessory drive.
Remove air compressor (6) from the engine.
Illustration 3 g00929487
Typical example
Remove O-ring seal (7) from the air compressor.Note: Install Tooling (A) to the mounting flange of the air compressor. Tooling (A) will keep the drive gear stationary. The retaining nut for the drive gear can be removed.
Remove retaining nut (8) for the drive gear.
Remove the air compressor drive gear from the air compressor.Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     132-5451     Holding Fixture     1    
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Install the air compressor drive gear onto the shaft of the air compressor.
Illustration 4 g00929487
Typical exampleNote: Install Tooling (A) to the mounting flange of the air compressor. Tooling (A) will keep the drive gear stationary. The retaining nut for the drive gear can be installed.
Install retaining nut (8) for the drive gear. For compressors that have a straight shaft, refer to Step 3 in order to tighten nut (8) . For compressors that have a tapered shaft, refer to Step 4 in order to tighten nut (8) .
Tighten retaining nut (8) to a torque of 460 60 N m (339 44 lb ft).
Tighten nut (8) to a torque of 170 15 N m (125 11 lb ft). Place a driver which is slightly larger than nut (8) over nut (8) and tap the driver with a hammer. Tighten nut (8) again to a torque of 170 15 N m (125 11 lb ft).
Install new O-ring seal (7) on the air compressor.
Position air compressor (6) on the engine.


Parts bracket Mercruiser:

898101673
BRACKET
898101673 BRACKET
40200002D, 40200002G
879172053
BRACKET
879172053 BRACKET
40200002D, 40200002G
879172054
BRACKET
879172054 BRACKET
40200002D, 40200002G
898101670
BRACKET
898101670 BRACKET
40200002D, 40200002G
898101676
BRACKET
898101676 BRACKET
40200002D, 40200002G
898101675
BRACKET
898101675 BRACKET
40200002D, 40200002G
898101678
BRACKET
898101678 BRACKET
40200002D, 40200002G
879312T27
BRACKET, Sterdrive Gear Shift
879312T27 BRACKET, Sterdrive Gear Shift
40200002D, 40200002G, 40280002D, 40420002D
Back to top