8M2004597 Mercruiser BRACKET, Cover, Oxygen Sensor


8M2004597 BRACKET, Cover, Oxygen Sensor Mercruiser 40500120U, 41510P1UE BRACKET
8M2004597 BRACKET, Cover, Oxygen Sensor Mercruiser
Rating:
38

Buy BRACKET, Cover, Oxygen Sensor 8M2004597 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.65
 

07-10-2017
.8[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 8M2004597 Bracket- Cover 02
Number on catalog scheme: 12
 

Compatible models:

40500120U   41510P1UE   Mercruiser

Mercruiser entire parts catalog list:

40500120U 1998
41510P1UE 1998

Information:


It is important that the electrical connections to the sender unit are connected correctly. If the cold start advance unit fails to operate correctly, engine damage may result because the engine timing will be fully advanced for normal engine operation.
The cold start advance unit is on the rear of the timing case on the left side of the engine.
Damage to the engine will occur if the engine is load tested at more than 80 percent of full load with the cold start advance unit disconnected.
Illustration 1 g00849690
Delphi DP200 fuel injection pump
(1) Engine stop solenoid
(2) 3 Amp wire
(3) Sending unit
(4) 3 Amp wire
(5) 6 Amp wire
(6) Fuel injection pump
(7) Cold start advance unit
(8) Start switch
Illustration 2 g00849700
Bosch fuel injection pump
(1) Fuel injection pump
(2) 3 Amp wire
(3) Engine stop solenoid
(4) Sending unit
(5) 3 Amp wire
(6) Cold start advance unit
(7) 6 Amp wire
(8) Start switch The cold start advance unit on the Delphi and the Bosch fuel injection pumps operate in a similar manner. As the engine begins to reach normal operating temperature, the cold start advance unit energizes. By energizing, the fuel injection pump timing is retarded to the correct timing for normal operation.
Damage to the engine will occur if the engine is load tested at more than 80 percent of full load with the cold start advance unit disconnected.
Illustration 3 g00849711
Stanadyne fuel injection pump
(1) Engine stop solenoid
(2) 3 Amp wire
(3) 6 Amp wire
(4) Fuel injection pump
(5) Cold start advance unit
(6) 3 Amp wire
(7) Sending unit
(8) Start switch The cold start advance unit on the Stanadyne fuel injection pump operates differently. As the engine begins to reach normal operating temperature, the cold start advance unit will de-energize. By de-energizing, the fuel injection pump timing is retarded to the correct timing for normal operation.Cold Starting Aid
Illustration 4 g00849717
Cold starting aid
(1) Connection for the advance lever to the pull rod
(2) Pull rod
(3) Electrical connection
(4) Element
(5) Advance lever
(6) Mounting bracket
(7) Battery Note: The advance lever (5) of the fuel injection pump is set at the factory in order to advance the injection timing when the engine is cold. The cold start advance unit must be energized, when the static timing of the fuel injection pump is checked.Note: Do not release the connection (1). The adjustment of the advance lever that is set in the factory will not be maintained.
Illustration 5 g00849720
(8) Locking plate
(9) Locking bolt Note: Before the crankshaft is turned or before the fuel injection pump is turned, loosen the locking bolt (9). Put the locking plate (8) under the locking bolt (9).Note: The crankshaft must not be moved, when the fuel injection pump is not on the engine. Movement of the crankshaft may result in damage to the timing case. If the crankshaft is moved, it may be necessary to reset the timing of the engine prior to the installation of the fuel injection pump.
Remove the fuel injection pump from the engine.
The positive terminal of the battery (7) is connected to the electrical connection (3) of the cold start advance unit by a wire.
The negative terminal of the battery (7) is connected to the mounting bracket (6) of the cold start advance unit by a wire.
Allow a minimum of five minutes for the wax in the element (4) to expand before the static timing is set.
Turn the pump shaft in the direction of rotation. The advance lever (5) will move toward the connection (1). There should be zero advance timing in this position. The pull rod (2) should be fully extended. Only trained personnel should perform any adjustments that are required. Note: The pump can be removed and the pump can be installed without energizing the cold start advance unit if the following conditions exist:
The performance of the fuel injection pump is correct.
The static timing adjustment is not necessary.


Parts bracket Mercruiser:

61897T
BRACKET, Rear Upper
61897T BRACKET, Rear Upper
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430L000JS
807979T
BRACKET
807979T BRACKET
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4262C01JT, 4332087N1, 4350104KS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 4454118JT, 4542067LS, 457B101KS, 4652027LE, 4652027M
863211T01
BRACKET, Alternator Mounting
863211T01 BRACKET, Alternator Mounting
40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M4102LRS, 4M4102LTS
879172T
BRACKET, Oil Filter Mount
879172T BRACKET, Oil Filter Mount
40500010U, 40500120U, 4S42028UU, 4S420P8UE
8M2006728
BRACKET, Pressure Hose Mount
8M2006728 BRACKET, Pressure Hose Mount
40500010U, 40500120U, 4S42028UU, 4S420P8UE
879194T
BRACKET, Filter Hose Clamp
879194T BRACKET, Filter Hose Clamp
40500010U, 40500120U, 4S42028UU, 4S420P8UE
Back to top