811377 Mercruiser BUSHING


811377 BUSHING Mercruiser 40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND BUSHING
811377 BUSHING Mercruiser
Rating:
63

Buy BUSHING 811377 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Mercruiser entire parts catalog list:

40280001D 1998
40420001D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C72040TD 1998
4C8204DLD 1998
4CJ2040ND 1998

Information:

Early engines use two bolts to hold the plate to the camshaft. Later engines use only one bolt to hold the plate to the camshaft.2. Remove the bolts and the plate from camshaft drive gear (1) on the right side camshaft. Use tooling (A) to remove camshaft drive gear (1), and the camshaft drive gear on the left side camshaft.3. Put stands or blocks under the rear of the engine as support. The weight of the engine is approximately 6131 kg (13,515 lb.).
Typical Example4. Fasten a hoist to flywheel housing (2), and remove the bolts that hold it. Remove flywheel housing (2) from the end of the cylinder block. The weight of flywheel housing (2) is 202 kg (445 lb.).Install Flywheel Housing
1. Use 6V1541 Quick Cure Primer to clean the mating surfaces of the flywheel housing and the cylinder block. Put 6V6640 Gasket Maker on the surfaces of the flywheel housing that makes contact with the cylinder block.
Typical Example2. Install two 5/8"-11 NC guide bolts in the rear of the cylinder block. Fasten a hoist, and put flywheel housing (1) in position on the guide bolts. 3. Install the bolts in their respective locations. See the Installation Chart. Tighten the 1/2"-NC bolts to a torque of 135 15 N m (100 11 lb.ft.). The 5/8"-11 NC bolts are tightened to a torque of 270 25 N m (200 18 lb.ft.). Cut the flywheel housing gasket even with the bottom of the cylinder block. For correct timing, all gear clearance (backlash) must be removed. Turn camshaft drive gears (2) in the same direction as the crankshaft rotation and hold in this position.4. Put camshaft drive gears (2), plate (3) and the tachometer drive adapter assembly in position on the ends of the camshafts. Install the bolts that hold them. Early engines use two bolts to hold plate (3) and the tachometer drive adapter assembly to the camshafts. Later engines use only one bolt to hold the plate and adapter assembly to the camshafts.5. Tighten the bolt for the single bolt adapter and plate as follows:a. Tighten the bolt to a torque of 360 40 N m (270 30 lb.ft.).b. Hit the adapter and plate with a hammer to seat the gear on the camshaft.c. Tighten the bolt again to a torque of 360 40 N m (270 30 lb.ft.).d. Repeat steps 5b and 5c until the torque does not change.6. Tighten the bolts for the two bolt adapter and plate assembly as follows:a. Tighten the bolts evenly to a torque of 100 15 N m (75 11 lb.ft.).b. Hit the adapter and plate with a hammer to seat the gear on the camshaft.c. Tighten the bolts again to a torque of 100 15 N m (75 11 lb.ft.).d. Repeat steps 6b and 6c until the torque does not change.
Typical Example7. Put gasket (5) and cover (4) in position on the flywheel housing, and install the bolts that hold them in place.End By:a. install crankshaft rear seal and wear sleeveb. install tachometer drivec. install oil pan (rear half only)d. install air startere. install engine


Parts bushing Mercruiser:

855461
 
855461 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801333864
 
801333864 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801331712
 
801331712 BUSHING
442B110GD, 442B115KD
811376
 
811376 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801331745
 
801331745 BUSHING
442B110GD, 442B115KD
881796
BUSHING
881796 BUSHING
442B110GD, 442B115KD
801763874
 
801763874 BUSHING
40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
854090
BUSHING
854090 BUSHING
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
Back to top