847637 Mercruiser BUSHING, Use Without Trim Senders

1. Remove oil line (1), fuel line (2) and clip (3). Use tool (A) to slide the sleeve into the head. 2. With tooling (B) in place, remove clip and pin (4). 3. Remove three bolts (5). Remove the governor with the O-ring seal. Care must be taken not to damage the fuel control linkage. Install in reverse order. After installation, check the Fuel Setting Adjustment. Refer to Systems Operation Testing And Adjusting, Form No. SENR3583.Disassemble & Assemble Fuel Transfer Pump
Start By:a. remove governor and fuel transfer pump 1. Install governor on governor repair stand (A).
There is spring force behind cover (1). Hold cover (1) in position, and slowly remove bolts (2), to release the spring force.
2. Remove three bolts (2) and cover (1). 3. Remove fitting (3) and the check valve from cover (1). Inspect parts for wear. 4. Remove spring (4), piston (5) and inspect for wear. Replace the spring and the complete piston assembly if necessary.5. Remove upper O-ring (6). 6. Remove sleeve assembly (7). Inspect tappet face (8) for wear. Replace complete assembly if necessary. Inspect cam surface, if damaged, replace the front housing assembly.7. Remove lower O-ring seal (9). 8. Remove fitting (10) and the check valve. Inspect for wear. The following steps are for the assembly of the fuel transfer pump.9. Lightly lubricate fitting (10) and the check valve bore with engine oil. Install the check valve with the sealing face down. With the O-ring in place, install fitting (10).10. Lubricate the sleeve bore. Install lower O-ring seal (9). Apply 8T2998 Camshaft Lubricant to tappet face (8). Slide sleeve assembly (7) into place, aligning the flat on the sleeve with the flat on the housing bore. Install upper O-ring (6).11. Lightly lubricate piston assembly (5) with engine oil. Install piston assembly (5) and spring (4).12. Lightly lubricate fitting (3) and the check valve bore with engine oil. Install the check valve with the sealing face toward the fitting. With the O-ring in place, install fitting (3).13. Position cover (1) compressing spring (4), and install bolts (2).14. Remove governor from tool (A).End By:a. install governor and fuel transfer pumpRemove & Install Fuel Ratio Control
Start By:a. remove shutoff solenoidb. remove governor and fuel transfer pump 1. Install the governor on governor repair stand (A). 2. Remove bolt (1) and clamp (2). Remove fuel ratio control assembly (3) by working stem (4) out of work (5). The following steps are for the installation of the fuel ratio control.
When removing plug (6), care must be taken to avoid damaging the internal parts of the governor.
3. Remove housing plug (6), using the blade of a screwdriver, accessed thru the fuel ratio control assembly location in the governor housing. This exposes adjustment screw (7).4. Install the fuel ratio control assembly, insuring that stem (4) is engaged thru fork (5). [Reach thru the other side to help engage fork (5)].5. Position clamp (2) and install bolt (1).End By:a. calibrate governor, (including the fuel ratio control), using Special Instruction Form No. SEHS8868 (Using 1U7326 Governor Calibration Bench).
Use care when applying sealant to the plug. The sealant must not be permitted to enter the governor housing.
Apply 5P3413 Sealant to the plug and install the plug in the housing bore. Expand the plug by carefully tapping the center of the plug with a hammer and a blunt ended punch until the plug is tight in the bore.b. install Plug 7C6204 (and Plug 7C6205 if not equipped with fuel ratio control) using Sealant 5P3413.c. install governor and fuel transfer pumpd. install shutoff solenoid.Disassemble & Assemble Governor Spring Group
Start By:a. remove shutoff solenoidb. remove governor 1. Mount the governor on governor repair stand (A) positioned on the drive gear end.2. Remove fitting (1), three bolts (2) and cover assembly (3). 3. Remove rear spring seat (4) (dashpot equipped governors only), shims (5) and spacer (6). 4. Remove the spring and seat assembly (9). Spring (7) can be removed by unscrewing spring coils from molded spring seat (9).5. Remove snap ring (8) and the inner springs from molded spring seat (9). Replace as a spring group package only. Dashpot spring, if governor is so equipped, need not be replaced as part of the governor spring package. The following steps are for the installation of the governor spring group.6. Screw the governor springs onto molded spring seat (9). Visually align springs so that they are square with the seat assembly and each other. Install the spacer, the ring and the snap ring.7. Slide seat assembly (9) and the springs onto the riser shaft with the springs facing up. 8. Install the rear spring seat (if applicable), shims (5) and spacer (6). If governor is equipped with dashpot (10), be sure the dashpot piston is piloted in rear of the spring seat.9. Remove O-ring (11). Lightly lubricate the housing bore with engine oil, and loosely fit the rear cover assembly into place. The oil in rear cover sump (12), should be drained. 10. Remove screen assembly (12). 11. Install tooling (B) and set the dial indicator probe on the center of the rear cover. To zero the indicator, push the rear cover assembly down until it makes contact with the governor housing and then zero the indicator. Release the cover and as the spring pushes up. Rotate it approximately 1/4turn, then read the indicator. Add or subtract shims (5) to achieve the correct spring preload dimension. Rear cover assembly must move freely. Refer to the Governor Performance Data Fiche for the correct spring preload dimension in MM, according to the governor group number.12. Remove tool (B) and cover assembly (3). Install the o-ring seal on cover assembly (3). Position cover and install bolts (2).13. Install fitting (1).End By:a. calibrate governor using Special Instructions, Form No. SEHS8868, and (Using 1U7326 Governor Calibration Bench).b. install a new Plug 7C6204 (and Plug 7C6205, if not equipped with fuel ratio control) using Sealant 5P3413c. install governord. install shutoff solenoid.Disassemble & Assemble Torque Cam
Start By:a. remove the shutoff solenoidb. remove the