17647 Mercruiser CAP, RESERVOIR USE W/DIPSTICK

Table 1
Diagnostic Trouble Codes
J1939 Code Code Description
(code descriptions may vary) Comments
102-1 Engine Intake Manifold #1 Pressure : Low - most severe (3) The code is logged.
Engine power is derated.
102-18 Engine Intake Manifold #1 Pressure : Low - moderate severity (2) The code is logged.
Engine power is derated.
2630-1 Engine Charge Air Cooler Outlet Temperature : Low - most severe (3) The code is logged due to a restriction in the intake manifold that can be caused by icing.
Follow the troubleshooting procedure in order to identify the root cause of the problem.
Table 2
Associated Diagnostic Trouble Codes
107-15
107-16
Table 3
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Connect to Caterpillar Electronic Technician (ET).
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Determine if an associated code listed in Table 2 is active or logged. Table 2 lists associated diagnostic codes.
Codes
Result: An associated code is active.
Refer to Troubleshooting, "Diagnostic Trouble Codes" in order to troubleshoot the associated diagnostic code.
Result: An associated code is not active or logged.
Proceed to Test Step 2.
2. Check the Air Inlet System for Restrictions
A. Visually inspect the air filter for cleanliness on engines without an electronic monitoring system on the inlet air system. A mechanical indicator may be used to monitor inlet air restrictions. Use the indicator to determine the cleanliness of the inlet air system. Also, inspect the piping for restrictions.
Restrictions
Result: The air filter is clean and a restriction is not found.
Proceed to Test Step 3.
Result: The inlet air system is restricted.
Clean the filter or replace the filter. Remove all obstructions in the inlet air piping. Verify that the problem has been resolved. If the problem still exists, proceed to Test Step 3.
Illustration 1 g03777706
Typical points of inspection
Table 4
Troubleshooting Test Steps Values Results
3. Inspect the Air Piping and Connections
A. Inspect the piping and the hose connections from the turbocharger compressor outlet to the Air to Air Aftercooler (ATAAC) inlet (if equipped). Remove the hose connections and inspect the hose connections for cuts or damage.
Connections
Result: The piping or hose connections were damaged.
Replace the damaged piping or hose connections. Verify that the problem has been resolved.
If the problem still exists, proceed to Test Step 4.
Result: The piping was not damaged.
Proceed to Test Step 4.
4. Perform Turbocharger Compressor Bypass Valve Test
A. Perform the "Turbocharger Compressor Bypass Valve Test" in Cat ET. The test will verify that the Turbocharger Compressor Bypass Valve is working properly.
Turbocharger Compressor Bypass Valve Test
Result: The Turbocharger Compressor Bypass Valve Test did not complete successfully.
Replace the Turbocharger Compressor Bypass Valve. Verify that the problem has been resolved. Perform the Turbocharger Compressor Bypass Valve Test.
Return the engine to service if the test was successful. If the test was not successful, proceed to Test Step 5.
Result: The Turbocharger Compressor Bypass Valve Test did complete successfully.
Proceed to Test Step 5.
5. Inspect the Turbocharger
A. Remove the connection for the inlet air and the exhaust connection to the turbocharger. Verify that the compressor wheel and the turbine wheel are spinning freely. Verify that the compressor wheel and the turbine wheel are not damaged.
Turbocharger
Result: The turbocharger wheels are damaged.
Replace the turbocharger. Return the unit to service.
Complete the procedure in the order in which the steps are listed.