8M2004059 Mercruiser CAP, Vent


8M2004059 CAP, Vent Mercruiser 41510P1UE CAP
8M2004059 CAP, Vent Mercruiser
Rating:
18

Buy CAP, Vent 8M2004059 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$22.99
 

22-04-2021
0.29982867632[0.00] Pound
-: -
New Mercury Mercruiser Quicksilver Oem Part # 8M2004059 Cap-Vent
Number on catalog scheme: 30
 

Compatible models:

41510P1UE   Mercruiser

Mercruiser entire parts catalog list:

41510P1UE 1998

Information:


Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledgeMechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).MEUI A Injector Adjustment
Table 1
Required Tools
Part Number Part Name Quantity
9U-7227 Injector Height Gauge 1
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height GaugeTo adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Injector height gauge (4) is used to obtain a dimension of 78.0 0.2 mm (3.07 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body.
Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body.
Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body.
Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 10 N m (74 7 lb ft).
To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke.
Repeat Steps 3 through 4.
Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.MEUI C Injector Overview
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connectorMechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).MEUI C Injector Adjustment
Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Set injectors 3, 5, and 6 using the procedure that follows.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).


Parts cap Mercruiser:

72058
 
72058 CAP, BOTTLE
02297343, 03307332, 03308333, 04544347, 04856332, 40420001D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 42
FI1100604
 
FI1100604 CAP
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430L000JS
806727 1
CAP
806727 1 CAP
40200002D, 40200002G, 40420001D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4231017L1, 424106LR
8M2000826
 
8M2000826 CAP
41000001S, 41000008E, 41510P1UE
885179
CAP
885179 CAP
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 41510P1UE, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
811635T 3
CAP, Distributor
811635T 3 CAP, Distributor
4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE
899871001
 
899871001 CAP, Rubber
4111021UT, 4111021UU, 41510P1UE
8M2004060
Back to top