34480 Mercruiser CLAMP UNIT, DISTRIBUTOR SERIAL


34480 CLAMP UNIT, DISTRIBUTOR SERIAL Mercruiser 2165203, 2165208 CLAMP
34480 CLAMP UNIT, DISTRIBUTOR SERIAL Mercruiser
Rating:
18

Buy CLAMP UNIT, DISTRIBUTOR SERIAL 34480 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 42
 

Compatible models:

2165203   2165208   Mercruiser

Mercruiser entire parts catalog list:

2165203 1973,1974,1975,1976,1977
2165208 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description QTY
A 4C-5599 Anti-Seize Compound 1
B - Loctite 271 1 Start By:
Drain the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
The engine can start automatically. Ensure that the power supply is isolated before any service or repairs is performed.
Disconnect the exhaust elbow from the turbocharger.
Disconnect the air inlet from the turbocharger.
Loosen clamp and disconnect the air outlet hose from the turbocharger.
Remove the blanket from the turbocharger.
Disconnect the tube assembly from turbocharger turbine housing.
Illustration 1 g03343661
Follow Steps 7.a through 7.c in order to remove hose and tube assembly (2).
Remove bolts (1).
Remove banjo bolt (7) and remove sealing washers (9).
Remove hose and tube assembly (2) from the cylinder block. Remove gasket (3). Note: Plug the port for the oil feed to the turbocharger with a suitable plug.
Follow Steps 8.a through 8.c in order to remove hose and tube assembly (8).
Remove bolts (10).
Remove bolts (6) and remove hose and tube assembly (8) from turbocharger (4). Note: Plug the port for the tube assembly to the turbocharger with a suitable plug.
Remove gasket (5) and remove gasket (11).
Illustration 2 g03343708
Remove bolts (15) and nuts (16) from turbocharger (4) and remove turbocharger (4) from exhaust manifold (14). Discard bolts (15) and nuts (16).
Remove gasket (13).
If necessary, remove studs (12) from turbocharger (12). Installation Procedure
Illustration 3 g03343708
Ensure that the turbocharger is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If any part of the turbocharger is worn or damaged, the complete turbocharger must be replaced.
Clean the gasket surfaces of exhaust manifold (14). If necessary, install studs (12) to the turbocharger. Apply Tooling (B) to the threads of studs (12). Install studs to the turbocharger and tighten securely.
Illustration 4 g03372483
Typical Example
If a new turbocharger is installed, bearing housing (18) and compressor housing (19) must be oriented to the correct positions. Follow Step 3.a through Step 3.d in order to orient the bearing housing and the compressor housing.
Loosen band clamps (20) sufficiently in order to allow the housings to rotate. Note: If the band clamps are damaged, replace the band clamps.
Carefully turn bearing housing (18) until the port for oil feed (17) is upward.
Rotate compressor housing (19) until the compressor outlet is in the correct position. Refer to the turbocharger that was originally installed for the correct orientation.
Ensure that band clamps (20) are correctly oriented. Refer to the turbocharger that was originally installed for the correct orientation. Tighten the band clamps finger tight.
Install a new gasket (13) to exhaust manifold (14).
Align turbocharger (4) with outlet hose. Install new bolts (15) and new nuts (16). Tighten the nuts and the bolts to a torque of 44 N m (33 lb ft).
Illustration 5 g03343661
Ensure that hose and tube assembly (2) and (8) are clean and free from damage. Replace any damaged components.
Position a new gasket (3) and bolts (1) onto hose and tube assembly (2).
Install hose and tube assembly (2) to turbocharger (4). Tighten bolts (1) finger tight.
Position a new gasket (11) between the hose and tube assembly (8) and the cylinder block. Install bolts (10) finger tight.
Position a new gasket (5) and bolts (6) on to hose and tube assembly (8). Install tube assembly (8) to turbocharger. Tighten bolts (6) finger tight.
Remove the plug from the oil inlet port. Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Install banjo bolt (7) and two new sealing washers (9) to hose and tube assembly (2).
Install hose and tube assembly (2) to the cylinder block and to turbocharger (4). Tighten banjo bolt (7) finger tight.
If a new turbocharger has been installed, check that the orientation of the bearing housing is correct. If the orientation of the bearing housing is not correct, rotate the bearing housing until tube assembly (9) fits correctly. Tighten the band clamps to a torque of 13 N m (9.6 lb ft).
Tighten banjo bolt (7) to a torque of 20 N m (14 lb ft).
Tighten bolts (6) and bolts (10) to a torque of 28 7 N m (21 5 lb ft)


Parts clamp Mercruiser:

64648
 
64648 CLAMP, VENT HOSE
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208
62420
 
62420 CLAMP, DISTRIBUTOR
2165203, 2165208
72624
 
72624 CLAMP, DISTRIBUTOR(SERIAL# AND UP
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
22740
 
22740 CLAMP, WIRING HARNESS TO EXHAUST MANIFOLD 93/8")-
03302336, 03307332, 2165203, 2165208, 5120150AR, 5220200AS, 91331015
65653
 
65653 CLAMP, FUEL LINE TO ROCKER COVER
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 411102KN2, 430B00001, 430L000JS, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
64646
54178
 
54178 CLAMP, TEMPERATURE SENDER WIRE
02287333, 03302336, 03307332, 2165203, 2165208, 228801
Back to top