882748 Mercruiser CLIP


882748 CLIP Mercruiser 4V71222ND, 4V71222PD, 4V71222TD CLIP
882748 CLIP Mercruiser
Rating:
98

Buy CLIP 882748 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$39.60
 

12-01-2024

Amazon.com
GSP 882748 Loaded Strut and Coil Spring Assembly - Compatible With Select Chevrolet Cruze Eco
GSP GSP Loaded Strut Assemblies come complete with high quality struts, coil springs, strut mounts, and hardware and are ready to install, right out of the box, making installation quicker and easier || All new components, engineered to provide OE form, fit, and function, are used to manufacture our loaded strut assemblies, ensuring that ride comfort and handling are returned to factory fresh levels || Struts feature hi-performance 'Tri-Lock' PTFE piston rod seals, chrome plated piston rods, and a nitrogen gas charge; quality components and engineering ensure long term durability and heat resistance || Coil springs feature cold rolled SAE 9254 rated spring steel for strength and durability; premium quality strut mounts are designed to eliminate transfer of harmonic resonance to the vehicle body || Struts and springs are tuned specifically to each vehicle application to provide OE levels of comfort and stability regardless of road conditions or speed
Number on catalog scheme: 2
 

Compatible models:

Mercruiser entire parts catalog list:

4V71222ND 1998
4V71222PD 1998
4V71222TD 1998

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7094     Breaker Bar     1    
Illustration 1 g00711393
Illustration 2 g00711616
Insert Tool (A) (not shown) into notch (X). Use Tool (A) in order to release the tension on four V-belts (8). Remove the V-belts from idler pulley (4) .
Disconnect hose assembly (3) from tightener arm assembly (7) .
Remove the cotter, the washer, and clevis pin (2) that holds spring (1) to the belt tightener. Repeat for the remaining spring.
Remove bolt (6), the washer, and retainer plate (5) that holds tightener arm assembly (7) in position.
Remove tightener arm assembly (7) and idler pulley (4) from the shaft as an assembly.
Illustration 3 g00711395
Remove four bolts (13), the hard washers, cover (14), and the gasket from idler pulley (4) .
Remove bolt (15) and retaining washer (16) .
Remove idler pulley (4), spacer (18), and O-ring seal (17) from tightener arm assembly (7) .
Remove ball bearing (12), spacer (11), ball bearing (10), and lip seal (9) from idler pulley (4) .Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7094     Breaker Bar     1    
B     1P-0510     Driver Group     1    Note: Check all of the O-ring seals and the components for wear or for damage. Replace the components, if necessary. Lubricate all of the O-ring seals lightly with the lubricant that is being sealed. Clean all of the components with a cloth that is free of loose material (lint).
Illustration 4 g00711395
Install O-ring seal (17) and spacer (18) on tightener arm assembly (7). Install ball bearing (10) in idler pulley (4) .
Lubricate lip seal (9) with 1P-0808 Multipurpose Grease. Use Tooling (B) (not shown) in order to install lip seal (9) in idler pulley (4). Make sure that the lip of the seal is positioned toward the inside of the idler pulley, as shown.
Position idler pulley (4) on tightener arm assembly (7). Make sure that lip seal (8) contacts spacer (17). Install spacer (10) and ball bearing (11) on the shaft of tightener arm assembly (7) .
Install retaining washer (16) and bolt (15). Position the gasket and cover (14) on idler pulley (4). Install four bolts (13) and the hard washers that hold cover (14) in position.
Illustration 5 g00711393
Illustration 6 g00711616
Position tightener arm assembly (7) and idler pulley (4) on the shaft as an assembly. Install retainer plate (5), the washer, and bolt (6) that holds tightener arm assembly (7) in position.
Position spring (1) to the belt tightener. Install clevis pin (2), the washer, and the cotter that holds spring (1) to the belt tightener. Repeat for the remaining spring.
Connect hose assembly (3) to tightener arm assembly (7) .
Insert Tool (A) (not shown) into notch (X). Use Tool (A) in order to release the spring tension so that four V-belts (8) can be installed on idler pulley (4) .
Illustration 7 g00711634
Lubricate fitting (19) with 1P-0808 Multipurpose Grease in order to grease the belt tightener.Note: Fitting (19) is located below the alternator on the front right side of the engine.


Parts clip Mercruiser:

816398
 
816398 CLIP (NEW DESIGN)
257B021JS, 4052110CR, 4211015L1, 4231017L1, 4262C01JT, 4332087N1, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 444106LPS, 4454110AS, 457B100KS, 457B101JS, 457B101KS, 457L101JS, 474H110AR, 4M11025LS, 4M11025R
882424
CLIP, Fuel
882424 CLIP, Fuel
4V71222ND, 4V71222PD, 4V71222TD
882660
 
882660 CLIP, Hose
4V71222ND, 4V71222PD, 4V71222TD
882737
 
882737 CLIP, Injection Pipe
4V71222ND, 4V71222PD
882738
 
882738 CLIP, Injection Pipe
4V71222ND, 4V71222PD, 4V71222TD
882750
 
882750 CLIP
4V71222ND, 4V71222PD, 4V71222TD
882749
 
882749 CLIP
4V71222ND, 4V71222PD, 4V71222TD
883864
 
883864 CLIP
4V71222ND, 4V71222PD, 4V71222TD
Back to top