882749 CLIP Mercruiser
4V71222ND, 4V71222PD, 4V71222TD
CLIP
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$46.54
12-01-2024
Amazon.com
GSP 882749 Loaded Strut and Coil Spring Assembly - Compatible With Select Chevrolet Cruze Eco - Front Right (Passenger Side)
GSP GSP Loaded Strut Assemblies come complete with high quality struts, coil springs, strut mounts, and hardware and are ready to install, right out of the box, making installation quicker and easier || All new components, engineered to provide OE form, fit, and function, are used to manufacture our loaded strut assemblies, ensuring that ride comfort and handling are returned to factory fresh levels || Struts feature hi-performance 'Tri-Lock' PTFE piston rod seals, chrome plated piston rods, and a nitrogen gas charge; quality components and engineering ensure long term durability and heat resistance || Coil springs feature cold rolled SAE 9254 rated spring steel for strength and durability; premium quality strut mounts are designed to eliminate transfer of harmonic resonance to the vehicle body || Struts and springs are tuned specifically to each vehicle application to provide OE levels of comfort and stability regardless of road conditions or speed
GSP GSP Loaded Strut Assemblies come complete with high quality struts, coil springs, strut mounts, and hardware and are ready to install, right out of the box, making installation quicker and easier || All new components, engineered to provide OE form, fit, and function, are used to manufacture our loaded strut assemblies, ensuring that ride comfort and handling are returned to factory fresh levels || Struts feature hi-performance 'Tri-Lock' PTFE piston rod seals, chrome plated piston rods, and a nitrogen gas charge; quality components and engineering ensure long term durability and heat resistance || Coil springs feature cold rolled SAE 9254 rated spring steel for strength and durability; premium quality strut mounts are designed to eliminate transfer of harmonic resonance to the vehicle body || Struts and springs are tuned specifically to each vehicle application to provide OE levels of comfort and stability regardless of road conditions or speed
Mercruiser entire parts catalog list:
- WIRING HARNESS AND CLIPS » 882749
- WIRING HARNESS AND CLIPS » 882749
- WIRING HARNESS AND CLIPS » 882749
Information:
Note: Check all of the O-ring seals and the components for wear or for damage. Replace the components, if necessary. Replace all of the gaskets prior to assembly. Lubricate all of the O-ring seals lightly with the lubricant that is being sealed. Clean all of the components with a cloth that is free of loose material (lint).
Illustration 1 g00712036
Position a new gasket (30) on the engine block. Make sure that all four joints (X) of gasket (30) are positioned correctly. Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to each joint (X) .
Illustration 2 g00712008
Illustration 3 g00652707
Apply 4C-9508 Wicking Sealant to the eight 1/2 in - 13 NC twelve point head bolts (29). Use two people in order to lift oil pan (front) (26) into position, as shown. The weight of the oil pan (front) is 39 kg (85 lb). Install 17 twelve point head bolts (29) and the hard washers that hold oil pan (front) (26) in position.
Position plate (28) on oil pan (front) (26). Install two bolts (27) and the hard washers that hold plate (28) in position.
Position a new integral seal (not shown) on the surface of oil pan (front) (26) that mates with the oil pan (middle). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of the integral seal and gasket (30) .
Illustration 4 g00652705
Illustration 5 g00652706
Lift oil pan (middle) (22) into position, as shown. Install 12 bolts (24) and the hard washers that hold oil pan (middle) (22) in position.
Install eight bolts (23) and the hard washers that hold oil pan (middle) (22) to the oil pan (front).
Position a new integral seal (21) on the surface of oil pan (middle) (22) that mates with oil pan (rear) (19). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of integral seal (21) and gasket (30) .
Apply 4C-9508 Wicking Sealant to the two 1/2 in - 13 NC twelve point head bolts (25). Lift oil pan (rear) (19) into position, as shown. Install 11 bolts (25) and the hard washers that hold oil pan (rear) (19) in position.
Install eight bolts (20) and the hard washers that hold oil pan (middle) (22) to oil pan (rear) (19) .
Illustration 6 g00652704
Position support (18) on the oil pan (rear). Install four bolts (17) and the hard washers that hold support (18) in position.
Illustration 7 g00711824
Illustration 8 g00711857
Install two bolts (9) (not shown) and the hard washers that hold the two plates together.
Position seal (15) and O-ring seal (16) on oil pump inlet elbow (12). Position O-ring seal (14) on pump inlet elbow (8) .
Position oil pump inlet elbow (12) and pump inlet elbow (8) on the oil pan (front), as shown. Install five bolts (10), bolt (11), and the hard washers that hold oil pump inlet elbow (12) in position. Install two bolts (7) that hold pump inlet elbow (8) in position.
Connect wire harness (13) for the liquid level switch at the electrical connection.
Illustration 9 g00711770
Connect tube assembly (5) and hose assembly (6) to the oil pan (front).Note: Hose assembly (6) is only present on machines that are equipped with the engine prelubrication system.
Illustration 10 g00652699
Illustration 11 g00711796
Position tube assembly (dipstick) (2) to the oil pan. Install two nuts (1) and the hard washers that hold the lower end of tube assembly (2) in position. Tighten the nuts to a torque of 35 5 N m (26 4 lb ft).
Tighten bolt (3) and two clamps (4) that hold tube assembly (2) to the bracket. Repeat for the remaining two clamps.
Tighten the oil drain plug (not shown) to a torque of 110 15 N m (81 11 lb ft). Tighten the bolt (not shown) on the bottom of the oil pan (rear) to a torque of 55 7 N m (41 5 lb ft).
Fill the engine w
Illustration 1 g00712036
Position a new gasket (30) on the engine block. Make sure that all four joints (X) of gasket (30) are positioned correctly. Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to each joint (X) .
Illustration 2 g00712008
Illustration 3 g00652707
Apply 4C-9508 Wicking Sealant to the eight 1/2 in - 13 NC twelve point head bolts (29). Use two people in order to lift oil pan (front) (26) into position, as shown. The weight of the oil pan (front) is 39 kg (85 lb). Install 17 twelve point head bolts (29) and the hard washers that hold oil pan (front) (26) in position.
Position plate (28) on oil pan (front) (26). Install two bolts (27) and the hard washers that hold plate (28) in position.
Position a new integral seal (not shown) on the surface of oil pan (front) (26) that mates with the oil pan (middle). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of the integral seal and gasket (30) .
Illustration 4 g00652705
Illustration 5 g00652706
Lift oil pan (middle) (22) into position, as shown. Install 12 bolts (24) and the hard washers that hold oil pan (middle) (22) in position.
Install eight bolts (23) and the hard washers that hold oil pan (middle) (22) to the oil pan (front).
Position a new integral seal (21) on the surface of oil pan (middle) (22) that mates with oil pan (rear) (19). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of integral seal (21) and gasket (30) .
Apply 4C-9508 Wicking Sealant to the two 1/2 in - 13 NC twelve point head bolts (25). Lift oil pan (rear) (19) into position, as shown. Install 11 bolts (25) and the hard washers that hold oil pan (rear) (19) in position.
Install eight bolts (20) and the hard washers that hold oil pan (middle) (22) to oil pan (rear) (19) .
Illustration 6 g00652704
Position support (18) on the oil pan (rear). Install four bolts (17) and the hard washers that hold support (18) in position.
Illustration 7 g00711824
Illustration 8 g00711857
Install two bolts (9) (not shown) and the hard washers that hold the two plates together.
Position seal (15) and O-ring seal (16) on oil pump inlet elbow (12). Position O-ring seal (14) on pump inlet elbow (8) .
Position oil pump inlet elbow (12) and pump inlet elbow (8) on the oil pan (front), as shown. Install five bolts (10), bolt (11), and the hard washers that hold oil pump inlet elbow (12) in position. Install two bolts (7) that hold pump inlet elbow (8) in position.
Connect wire harness (13) for the liquid level switch at the electrical connection.
Illustration 9 g00711770
Connect tube assembly (5) and hose assembly (6) to the oil pan (front).Note: Hose assembly (6) is only present on machines that are equipped with the engine prelubrication system.
Illustration 10 g00652699
Illustration 11 g00711796
Position tube assembly (dipstick) (2) to the oil pan. Install two nuts (1) and the hard washers that hold the lower end of tube assembly (2) in position. Tighten the nuts to a torque of 35 5 N m (26 4 lb ft).
Tighten bolt (3) and two clamps (4) that hold tube assembly (2) to the bracket. Repeat for the remaining two clamps.
Tighten the oil drain plug (not shown) to a torque of 110 15 N m (81 11 lb ft). Tighten the bolt (not shown) on the bottom of the oil pan (rear) to a torque of 55 7 N m (41 5 lb ft).
Fill the engine w
Parts clip Mercruiser:
816398
816398 CLIP (NEW DESIGN)
257B021JS, 4052110CR, 4211015L1, 4231017L1, 4262C01JT, 4332087N1, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 444106LPS, 4454110AS, 457B100KS, 457B101JS, 457B101KS, 457L101JS, 474H110AR, 4M11025LS, 4M11025R
882424
882660
882737
882738
882748
882750
883864