74023A 1 Mercruiser HARNESS ASSEMBLY (USE WITHOUT FUSE)


74023A 1 HARNESS ASSEMBLY (USE WITHOUT FUSE) Mercruiser 00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015 HARNESS
74023A 1 HARNESS ASSEMBLY (USE WITHOUT FUSE) Mercruiser
Rating:
38

Buy HARNESS ASSEMBLY (USE WITHOUT FUSE) 74023A 1 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Mercruiser entire parts catalog list:

00014332 1982
01321017 1987
03301310 1980,1982,1983,1984,1985,1986,1987,1988,1989,1990,1993,1994
2140208 1978,1979,1980,1981,1982
2165208 1978
5220200AS 1988
91331015 1985,1986,1987

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 388-1289 Capping Kit 1 Start By:
If the Diesel Particulate Filter (DPF) assembly is mounted above the valve mechanism cover, removal of the DPF assembly and mounting bracket will be necessary. Refer to Disassembly and Assembly, "Diesel Particulate Filter - Remove" and Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedures.
Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) - Remove and Install" for the correct procedure.
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" for the correct procedure.
Remove the secondary fuel filter base. Refer to Disassembly and Assembly, "Fuel filter Base - Remove and Install (Secondary Fuel Filter)" for the correct procedure.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Plug or cap all open ports and tube assemblies.
Illustration 1 g02671257
If necessary, remove the exhaust gas recirculation valve (EGR Valve). Refer to Disassembly and Assembly, "Exhaust Gas Recirculation Valve - Remove and Install" for the correct procedure.
Remove bolts (2) and bolt (3) from valve mechanism cover (1).
Remove valve mechanism cover (1) from the cylinder head.
Illustration 2 g02671282
Typical example
Remove gasket (4). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g02671282
Typical example
Illustration 4 g02908978
Thoroughly clean all gasket surfaces of valve mechanism cover (1). Note: Ensure that the recess for the gasket is free from oil.
Clean the gasket surfaces of the cylinder head.
Install a new gasket (4) to valve mechanism cover (1). Note: Ensure that the gasket is fully seated into the groove of the valve mechanism cover.
Position valve mechanism cover (1) onto the cylinder head.
Install bolts (2) and bolt (3) to the valve mechanism cover.
Temporarily install the bolts used to secure the fuel manifold in Positions (X) finger tight.
Illustration 5 g02671296
Tighten the bolts in the numerical sequence that is shown in Illustration 5. Tighten the bolts 1 through 7 to a torque of 10 N m (89 lb in)Tighten the bolt 8 to a torque of 27 N m (239 lb in)Repeat Step 7 in order to ensure the correct torque.
Remove the bolts used to secure the fuel manifold in Positions (X).
If necessary, install the exhaust gas recirculation valve (EGR Valve). Refer to Disassembly and Assembly, "Exhaust Gas Recirculation Valve - Remove and Install" for the correct procedure. End By:
Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" for the correct procedure.
Install the secondary fuel filter base. Refer to Disassembly and Assembly, "Fuel filter Base - Remove and Install (Secondary Fuel Filter)" for the correct procedure.
Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) - Remove and Install" for the correct procedure.
If the Diesel Particulate Filter (DPF) assembly is mounted above the valve mechanism cover, install the DPF assembly and mounting bracket. Refer to Disassembly and Assembly, "Diesel Particulate Filter - Remove" and Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedures.


Parts harness Mercruiser:

70967
 
70967 HARNESS, DUMMY SENDER
00014332, 2140208, 2165208, 2250507
70968
 
70968 HARNESS, TRIM LIMIT SWITCH
00014332, 2140208, 2165208, 2250507
87394A20
 
87394A20 HARNESS ASSEMBLY, CONTROL PANEL
00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015
93542A 1
 
93542A 1 HARNESS ASSEMBLY, HYDRAULIC PUMP
00014332, 2140208, 2165208
79147A 1
 
79147A 1 HARNESS ASSEMBLY (USE WITH FUSE)
00014332, 2140208, 2165208
63405
 
63405 HARNESS, TRIM LIMIT SWITCH (PORT SIDE)
01321017, 03301310, 6030000ES
64987
 
64987 HARNESS, DUMMY SENDER (STARBOARD SIDE)
01321017, 03301310, 6030000ES
79147A 3
 
79147A 3 HARNESS ASSEMBLY, HYDRAULIC PUMP
00019003, 01321017, 01326013, 03301310, 4S42028N1, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5232100N1, 5C30150FS, 5E31200N1, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6
Back to top