807971 CONNECTOR, Hose Mercruiser
4231017L1, 4262C01JT, 4332087N1, 4350104KS, 457B101KS, 474L111JS, 4M31027LS
CONNECTOR
Price: query
Rating:
Mercruiser entire parts catalog list:
- FUEL PUMP AND FUEL COOLER » 807971
4332087N1 1998
- FUEL PUMP AND FUEL COOLER » 807971
- FUEL PUMP AND FUEL COOLER » 807971
- FUEL PUMP AND FUEL COOLER » 807971
- FUEL PUMP AND FUEL COOLER » 807971
- FUEL PUMP AND FUEL COOLER » 807971
Information:
1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap. 2. Remove bearing caps No. 2 through No. 6. Remove thrust plates from No. 4 upper bearing.3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 7 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 400 lb. (181 kg).
Be careful not to damage the crankshaft journals when the crankshaft is removed.
4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft. 5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block.
Use care to avoid damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
For more detail about installation of main bearings, see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearances with tool (B).7. Put clean engine oil on the bolts for caps No. 1 and No. 7. Install No. 1 and No. 7 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 4 upper main bearing. Install the thrust plates with the side that has identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 6. Install caps No. 2 through No. 6 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the end play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play with new thrust plates must be 0.006 to 0.020 in. (0.15 to 0.51 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Be careful not to damage the crankshaft journals when the crankshaft is removed.
4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft. 5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block.
Use care to avoid damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
For more detail about installation of main bearings, see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearances with tool (B).7. Put clean engine oil on the bolts for caps No. 1 and No. 7. Install No. 1 and No. 7 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 4 upper main bearing. Install the thrust plates with the side that has identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 6. Install caps No. 2 through No. 6 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the end play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play with new thrust plates must be 0.006 to 0.020 in. (0.15 to 0.51 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Parts connector Mercruiser:
805632
805632 CONNECTOR
02602347, 02608427, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS, 44541101S, 4454110GE, 4454110JT, 4454118JT, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JS, 474L118JT
805563
805563 CONNECTOR, (.500 Inch NPTF To .500 Inch Inverted Flare)
02602347, 02608427, 257B021JS, 4332087N1, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 44541101S, 4454110GE, 4454110JT, 4454118JT, 4502111FE, 457B100KS, 457B101JS, 457B111GS, 457L101JS, 473B1F0GS, 474L111JS, 474L118JS, 474L118JT, 4M11025LS, 4M11025RS,
808624
808624 CONNECTOR
40200002D, 40200002G, 40420001D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4231017L
806242
806242 CONNECTOR
40500006T, 40500010T, 40500010U, 40500120U, 4211015L1, 4231017L1, 444236HRS, 44541101S, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JS, 474L118JT, 4M4102LRS, 4M4102LTS
805592A 1
805592A 1 CONNECTOR
4231017L1, 4332087N1, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 4542067LS, 457B101JS, 457B101KS, 457B111GS, 457L101JS, 4652027M1, 4652227MW, 4M31027LS, 4R42027N1, 4S42028N1
808003
808003 CONNECTOR
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4262C01JT, 4332087N1, 4350104KS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 4454118JT, 4542067LS, 457B101KS, 4652027LE, 4652027M
807097T
807097T CONNECTOR
4231017L1, 4262C01JT, 4332087N1, 4350104JS, 4350104KS, 457B101JS, 457B101KS, 457L101JS, 474L111JS, 4M31027LS
808061