89772 Mercruiser CONNECTOR, (.125-27)


89772 CONNECTOR, (.125-27) Mercruiser 5220200AS, 91331015 CONNECTOR
89772 CONNECTOR, (.125-27) Mercruiser
Rating:
63

Buy CONNECTOR, (.125-27) 89772 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

5220200AS   91331015   Mercruiser

Mercruiser entire parts catalog list:

5220200AS 1988
91331015 1985,1986,1987

Information:


Illustration 1 g00998095
C-10 and C-12 map for very low oil pressure
Illustration 2 g00998096
3406E, C-15, C-16, and C-18 map for very low oil pressureSystem Response:The Caterpillar Electronic Technician (Cat ET) will display "LOW OIL PRESSURE" and "DIAG" next to the status for "Engine Oil Pressure". The check engine lamp and the warning lamp will illuminate.Customer passwords are required to clear this diagnostic code.The ECM will use the default torque map. The engine speed is limited to 1350 RPM and the vehicle speed is limited to 72 km/h (45 mph).Note: If the "Engine Monitoring" parameter is programmed to "Shutdown", the engine will be shutdown after this code has been active for 30 seconds.Note: If "Engine Monitoring" is programmed to "Warning" the engine power will not be affected.Test Step 1. Check the Engine Oil Level
Check the engine oil level.Expected Result:The engine oil level is OK.Results:
OK - The engine oil level is OK. Proceed to Test Step 2.
Not OK - The engine oil level is low.Repair: Add engine oil to the proper level. Refer to the Operation and Maintenance Manual for more information.STOPTest Step 2. Verify Proper Sensor Installation
Check the installation of the engine oil pressure sensor.
Check the wiring of the engine oil pressure sensor. Refer to the Electrical Schematic for the proper wiring. Ensure that all of the wires and connectors are properly connected.Expected Result:The sensor is properly installed and the wiring is correct.Results:
OK - The sensor is properly installed. Proceed to Test Step 3.
Not OK - The sensor is not installed properly.Repair: Install the engine oil pressure sensor properly. Repair the wiring and/or the connectors to the sensor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for Active Diagnostic Codes
Connect Cat ET to the data link connector.
Check for active diagnostic codes that are related to the barometric pressure sensor (atmospheric pressure) or the boost pressure sensor.Expected Result:There are no diagnostic codes that are related to the barometric pressure sensor (atmospheric pressure) or the boost pressure sensor.Results:
OK - There are no diagnostic codes. Proceed to Test Step 4.
Not OK - There is a diagnostic code that is related to the barometric pressure sensor (atmospheric pressure) and/or the boost pressure sensor.Repair: Troubleshoot the diagnostic code before continuing with this procedure.STOPTest Step 4. Check the Status Screen
Turn the keyswitch to the ON position. The engine should be off.
Monitor the status for "Boost Pressure" and "Engine Oil Pressure" on Cat ET.Expected Result:"Boost Pressure" and "Engine Oil Pressure" are less than 10 kPa (2 psi).Results:
OK - The boost pressure and the engine oil pressure are less than 10 kPa (2 psi). Proceed to Test Step 6.
Not OK - Boost Pressure - The boost pressure is greater than 10 kPa (2 psi). Proceed to Test Step 8.
Not OK - Engine Oil Pressure - The engine oil pressure is greater than 10 kPa (2 psi). Proceed to Test Step 9.
Not OK - Both - The boost pressure and the engine oil pressure are greater than 10 kPa (2 psi). Proceed to Test Step 5.Test Step 5. Check the Supply Voltage to the Pressure Sensors
Disconnect the barometric pressure sensor (atmospheric pressure), the boost pressure sensor, and the engine oil pressure sensor.
Turn the keyswitch to the ON position.
Measure the voltage between terminal A (Engine Pressure Sensor +5V) and terminal B (Engine Pressure Sensor Common) of each pressure sensor connector on the engine harness.Expected Result:The voltage is 5.0 0.16 VDC.Results:
OK - The voltage is within the range.Repair: Reconnect the engine oil pressure sensor and the boost pressure sensor.Temporarily connect a new barometric pressure sensor (atmospheric pressure).If the new sensor fixes the problem, reconnect the suspect sensor.If the problem returns, permanently replace the sensor.Verify that the repair


Parts connector Mercruiser:

47347
 
47347 CONNECTOR, HYDRAULIC - GIMBAL HOUSING
00014332, 01321017, 03301310, 2140208, 2165208, 2250507, 5220200AS, 6030000ES, 91331015
94275
 
94275 CONNECTOR, SOLENOID TO SOLENOID
00019003, 01321017, 01326013, 03301310, 40200002D, 40200002G, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5231100TP, 5232100N1, 5
70834
 
70834 CONNECTOR, Straight (.375-18 x .375)
41510P1UE, 444236HRS, 4M4102LRS, 4S42028N1, 5220200AS, 91331015
43711
 
43711 CONNECTOR
5120150AR, 5220200AS
85822
 
85822 CONNECTOR, Straight
5120150AR, 5220200AS
814382
 
814382 CONNECTOR
5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5232100N1, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910T
43828
 
43828 CONNECTOR
5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5232100N1, 5232100TP, 5C30150FS, 5E31200N1, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
18922
 
18922 CONNECTOR
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5220200AS, 5231100LP, 5C30150FS, 6020006JS, 6211001N1, 6311002NZ, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
Back to top