807371T Mercruiser COOLER-Oil


807371T COOLER-Oil Mercruiser 4454110JT, 4454118JT, 474L118JS, 474L118JT COOLER
807371T COOLER-Oil Mercruiser
Rating:
33

Buy COOLER-Oil 807371T Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$412.29
 

30-07-2024
0.0006[0.00] Pounds
US: Modern Boat Sales, I
QuickSilver Cooler-Engine
Quicksilver Quicksilver - Mercruiser 807371T, 710-807371T
$514.21
 

30-07-2024
0.0006[0.00] Pounds
US: Modern Boat Sales, I
Mercury/Quicksilver Parts Cooler-Oil-Engine 807371T 1
Quiksilver New
Number on catalog scheme: 12
 

Compatible models:

Mercruiser entire parts catalog list:

4454110JT 1996,1997
4454118JT 1996,1997
474L118JS 1996
474L118JT 1996,1997

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-5529 Piston Ring Compressor 1
B 4C-5593 Anti-Seize Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The joint between the connecting rod and the connecting rod cap is produced by fracturing. The connecting rod assembly must be handled with care in order to avoid damage to the mating surfaces. The connecting rod assembly must be replaced if any damage occurs to the mating surfaces. New connecting rod assemblies come with the connecting rod caps bolted on the connecting rod.Use only a soft jawed vise to hold the connecting rod assembly when removing the connecting rod cap bolts. Use only a soft faced hammer to tap the connecting rod cap when separating the connecting rod cap from the connecting rod.Failure to use a soft jawed vise and a soft faced hammer may result in damage to the connecting rod assembly.
Always use new connecting rod bolts during the installation of connecting rod assemblies that have fractured joints. Never reuse connecting rod bolts during the reassembly of fractured joint connecting rods.Reusing connecting rods bolts during reassembly of fractured joint connecting rods may result in engine damage.
Ensure that the fractured joints of the connecting rod are clean prior to installation. Use compressed air or a wire brush to clean the joints.
Apply clean engine oil to the pistons, the piston rings, and the cylinder bore.
Illustration 1 g00634923
Position the piston rings so that the end gaps are located 120 degrees from each other. Install Tooling (A) in order to compress the piston rings.
With the number one crankshaft throw at the bottom center, install the piston and connecting rod in the engine. Ensure that the proper piston and connecting rod are in the corresponding cylinder with the bearing retainer notch toward the right side of the engine. The etched number on the connecting rod must be positioned on the right side of the engine.
Line up the piston and the connecting rod with the crankshaft. Use a soft faced hammer and tap the piston into the cylinder bore until Tooling (A) comes off of the piston.
Illustration 2 g01062853
Before connecting rod (1) comes in contact with the crankshaft, install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (1).
Apply clean engine oil to the surface of the upper half of connecting rod bearing (4). Use a soft faced hammer in order to tap the piston into the cylinder bore while you guide connecting rod (1) onto the crankshaft.
Place the lower half of connecting rod bearing (5) in corresponding connecting rod cap (3). Ensure that the bearing tab engages with the groove in connecting rod cap (3).
Apply clean engine oil to the surface of the lower half of connecting rod bearing (5). Install connecting rod cap (3) on connecting rod (1). Ensure that the number on connecting rod cap (3) matches the number on connecting rod (1). Ensure that the numbers are on the same side.
Apply Tooling (B) to the new connecting rod bolts.
Install new connecting rod bolts (2). Tighten connecting rod bolts (2) to a torque of 70 5 N m (52 4 lb ft).
Place an index mark on each connecting rod bolt. Tighten each connecting rod bolt (2) for an additional 120 5 degrees (1/3 turn). End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".


Parts cooler Mercruiser:

99356A 2
 
99356A 2 COOLER, POWER STEERING FLUID
00014332, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 07711346, 08987343, 30001854, 40420001D, 428B116KD, 4350111HS, 442B110GD, 442B115KD, 443B0002S, 443B1003S, 4454110JT, 4454118JT, 457B101JS, 457B111GS, 473B1F0GS, 474L118J
807950A 1
 
807950A 1 COOLER, Fuel
4262C01JT, 4350104KS, 4350118KS, 4454118JT, 457B101KS, 474L111JS, 474L118JT
807292T
 
807292T COOLER, Power Steering Oil
257B021JS, 4262C01JT, 4350100KS, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 4454118JT, 457B100KS, 457B101JS, 457B101KS, 457L101JS, 474L111JS, 474L118JT, 4M31027LS
807371T 1
 
807371T 1 COOLER-Oil
4454118JT, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JT
807372T
 
807372T COOLER-Oil
4454118JT, 4652027LE, 4652027M1, 4652227MW
Back to top