882566 Mercruiser COOLER ASSEMBLY, Air


882566 COOLER ASSEMBLY, Air Mercruiser 4V71222ND, 4V71222PD, 4V71222TD COOLER
882566 COOLER ASSEMBLY, Air Mercruiser
Rating:
43

Buy COOLER ASSEMBLY, Air 882566 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$4,979.58
 

20-08-2018
80 Hundredths Pounds
Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 882566 Cooler
$4,979.58
 

07-10-2017

Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 882566 Cooler
Number on catalog scheme: 1
 

Compatible models:

Mercruiser entire parts catalog list:

4V71222ND 1998
4V71222PD 1998
4V71222TD 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-9120 Socket(1) 1
B 8T-5096 Dial Indicator 1
C - Loctite 5900 -
D 198-9113 Seal Installer 1
(1) Tooling (A) is a 46 mm socket.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377349
Install thrust washer (14) on the rear face of the crankshaft with the oil groove toward the outside.
Position the upper halves of crankshaft main bearings (13) in the cylinder block. Install the bearings with the main bearing tabs in the correct position. Lubricate the bearings with clean engine oil.
Illustration 2 g01377339
Lubricate the crankshaft journals with clean engine oil. Attach a suitable lifting device to crankshaft (12). The weight of crankshaft (12) is approximately 100 kg (220 lb). Use the suitable lifting device in order to position crankshaft (12) onto the upper halves of the crankshaft main bearings. Note: Be careful not to damage the finished surfaces on the crankshaft.
Illustration 3 g01377519
This Illustration is of the rear main bearing cap.
Install main bearings (11) onto crankshaft main bearing caps (7) (not shown). Install main bearing (11) onto rear main bearing cap (8). Install bearings (11) with the main bearing tabs in the correct position. Lubricate main bearings (11) with clean engine oil.
Install thrust washers (10) onto rear main bearing cap (8). Make sure that the oil grooves on thrust washers (10) are facing away from rear main bearing cap (8).
Illustration 4 g01377377
Illustration 5 g01377505
Apply Tooling (C) to the corners and the sides of rear main bearing cap (8). Install rear main bearing cap (8) to the cylinder block so that the rear face is even with the rear face of the cylinder block.
Apply soapy water to seals (9). Position seals (9) in the grooves on rear main bearing cap (8) with the rounded edges of seals (9) toward the outside. Use Tooling (D) in order to push seals (9) into position. This will reduce the risk of damaging the metal cores of seals (9). Apply Tooling (C) around seals (9). Cut off any excess length of seals (9).
Illustration 6 g01377316
Install crankshaft main bearing caps (7). Put clean engine oil on the threads of main bearing cap bolts (6). Install main bearing cap bolts (6). Tighten main bearing cap bolts (6) evenly to a torque of 137 5 N m (101 4 lb ft). Note: Ensure that crankshaft main bearing caps (7) are installed in the original locations.
Illustration 7 g01377571
Check the end play of the crankshaft with Tooling (B). The end play must be 0.100 to 0.264 mm (0.0039 to 0.0104 inch). Refer to the Specification, "Crankshaft" for more information on crankshaft end play.
Illustration 8 g01377310Note: Remove tape or rubber tubing from the connecting rod bolts.
Apply a light coat of clean engine oil to the connecting rod bearing surfaces and to the connecting rod journals. Install the connecting rods onto the connecting rod journals.
Install the lower half of the connecting bearings into the corresponding connecting rod caps and install connecting rod caps (5). Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in connecting rod caps (5). Install bolts (4) and the nuts. Tighten bolts (4) to a torque of 103 5 N m (76 4 lb ft).
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts cooler Mercruiser:

882709
 
882709 COOLER ASSEMBLY, Oil
4V71222ND, 4V71222PD, 4V71222TD
863939T
COOLER, Power Steering
863939T COOLER, Power Steering
4V71222ND, 4V71222PD, 4V71222TD
891791T
 
891791T COOLER, Transmission Oil
4V71222PD, 4V71222TD
Back to top