813971 Mercruiser COVER


813971 COVER Mercruiser 01207333, 01402414, 01407333, 01751347, 02602347, 02608427, 04544347, 06661346, 4052110CR, 430B00001, 44541101S, 4454110AS, 45021102S, 474H110AR COVER
813971 COVER Mercruiser
Rating:
28

Buy COVER 813971 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$36.76
 

15-12-2023
2.36[1.06] pounds
US: Race-Driven Inc
Sprocket for KTM 450 EXC 2007-2016 Rear 48 Tooth by Race-Driven
Race-Driven Brand New 48 Tooth Rear Steel Sprocket || Race-Driven sprockets are manufactured to exceed OEM specifications || Race-driven sprockets are produced using hardened S45C steel || Fits: 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 KTM 450 EXC
Number on catalog scheme: 22
 

Mercruiser entire parts catalog list:

01207333 1983
01402414 1984,1985,1986,1987,1988,1989
01407333 1983
01751347 1987,1988,1989,1990,1991,1992
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
04544347 1987
06661346 1986,1987,1988,1989
4052110CR 1990,1991,1992
430B00001 1990,1991,1992,1993,1994,1995
44541101S 1991,1992,1993,1994,1995,1996
4454110AS 1988,1989,1991,1992
45021102S 1992,1993
474H110AR 1988,1989,1990,1991

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02173073
If necessary, follow Step 2.a through Step 2.d in order to install bracket (29).
Position bracket (29) onto cylinder head (30).
Install bolts (28) hand tight. Ensure that rubber sleeve (32) is correctly positioned into recess of bracket (29).
Tighten bolts (28) to a torque of 22 N m (195 lb in).
Install new cable straps (31). Note: Ensure that the cable straps meet Original Equipment Manufacturers (OEM) specification.
Illustration 2 g02169940
Illustration 3 g02169941
Position a new gasket (15) onto inlet air control assembly (6). Ensure gasket (15) is correctly installed into locating Pins (A).
Loosen bolts (34) for bracket (33).
Illustration 4 g02169794
Illustration 5 g02351557
Illustration 6 g02169941
Position inlet air control assembly (6) onto bracket. Note: Ensure that the inlet air control assembly is correctly installed onto hose assembly for the inlet elbow.
Install bolts (25) and bolts (14) hand tight.
Tighten bolts (25) to a torque of 22 N m (195 lb in).
Tighten bolts (14) to a torque of 22 N m (195 lb in).
Tighten bolts (34) for bracket (33) to a torque of 44 N m (32 lb ft).
Connect temperature sensor (16) to the inlet air control assembly. Refer to Disassembly and Assembly, "Temperature Sensor (Cooled Exhaust Gas) - Remove and Install" for the correct procedure.
Install a new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) to tube assembly (23).
Position tube assembly (23) onto inlet air control assembly (6). Install install remaining new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) finger tight.
Install bolt (17) (not shown) and bolt (25) to clips for tube assembly (23).
Tighten banjo bolt (21) to a torque of 15 N m (133 lb in).
Tighten bolt (17) (not shown) and bolt (25) to a torque of 22 N m (195 lb in).
Install hose assembly onto turbocharger wastegate actuator and slide clip (19) along hose assembly. Note: Ensure that clip for hose assembly is correctly positioned onto the hose assembly.
Position a new hose clamp (17) and a new hose clamp (19) onto hose assembly (26) and hose assembly (27).
Install hose assembly (26) and hose assembly (27) to the connections on the inlet air control assembly (6).
Tighten hose clamp (17) and hose clamp (19) securely.
Illustration 7 g02169793
Connect hose assembly (7) to inlet connection (19) for inlet air control (6). Tighten hose clamps (8) to a torque of 6 N m (53 lb in).
Tighten hose clamps (12) for the hose assembly that connects inlet air control assembly (6) to inlet elbow (13). Tighten the hose clamps to a torque of 6 N m (53 lb in).
Slide connection for wiring harness assembly for wastegate solenoid (5) onto bracket (2). Connect the engine wiring harness assembly to wiring harness assembly for wastegate solenoid (5). Slide locking tab in to the locked position.
Slide connection for wiring harness assembly (4) onto bracket (2). Connect engine wiring harness assembly (1) to wiring harness assembly (4) for the NRS valve. Slide locking tab in to the locked position
Connect engine wiring harness assembly (10) to engine inlet throttle valve (11). Slide locking tab in to the locked position.
Install new cable straps to engine wiring harness assemblies. Ensure that all cable straps are installed to the harness assemblies. Note: Ensure that the cable straps meet OEM specification.


Parts cover Mercruiser:

7000
 
7000 COVER ASSEMBLY, FRONT
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
90670
 
90670 COVER ASSEMBLY, SLIP RING END
01206002, 01207333, 01326013, 01402414, 01406002, 01407333
75592
 
75592 COVER, ROCKER (RIGHT) QUANTITY OF 2 ON LATER ENGINES)
03302336, 03307332, 03308333, 04544347, 44031854
14043A 5
 
14043A 5 COVER ASSEMBLY, FLYWHEEL HOUSING
02297343, 03307332, 03308333, 04544347, 37011856
47441A 1
COVER, THERMOSTAT
47441A 1 COVER, THERMOSTAT
00014332, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08987343, 30001854, 32001876
17878A 5
 
17878A 5 COVER, FLAME ARRESTOR - NEW DESIGN
01207333, 01402414, 01407333, 01701335, 4111021L1, 411102KN2, 430B00001, 430L000JS
814702
 
814702 COVER, PUSH ROD
01207333, 01402414, 01407333, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
14249A 2
COVER, CRANKCASE FRONT
14249A 2 COVER, CRANKCASE FRONT
01751347, 02602347, 02608427, 32001876, 4350111HS, 457B101JS, 457B111GS
Back to top