811970 Mercruiser TAPERED ROLLER BEARING CUP


811970 TAPERED ROLLER BEARING CUP Mercruiser 428B116KD, 442B110GD, 442B115KD, 4A72040ND TAPERED
811970 TAPERED ROLLER BEARING CUP Mercruiser
Rating:
93

Buy TAPERED ROLLER BEARING CUP 811970 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$88.94
 

09-09-2022

-: -
Suspension Strut and Coil Spring Assembly Compatible with 97-03 Camry Solara
Fitment Notes: Fitment Notes Position = Front Right Engine Bore Inch = 3.48 Engine Stroke Inch = 3.78 || Direct fit replacement || Installs the same as factory unit || Same dimensions as Original Part
Number on catalog scheme: 35
 

Compatible models:

Mercruiser entire parts catalog list:

428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998

Information:

1. Fasten a hoist to implement pump (1) and remove the pump (if equipped). The weight of implement pump (1) is 29 kg (75 lb). 2. Remove plates (2).3. Remove pump drives (3) (if equipped) with Tool (A) and a hoist. The weight of each pump drive is 29 kg (65 lb). 4. Remove plate (4). 5. Remove starting motor (5) and disconnect oil supply line (6) at the flywheel housing. 6. Remove engine rear supports (7). 7. Remove turbocharger oil supply line (8) and bracket (9). 8. Remove top section of turbocharger heat shield (10). 9. Remove turbocharger drain line (11) and elbow (12). 10. Remove plate (13). 11. Remove bolts (14) and the remainder of the bolts which hold bracket (15) to the engine and remove bracket (15). 12. Use Tooling (A) and fasten a hoist to flywheel housing (16). Remove the bolts that hold flywheel housing (16) in position and pull flywheel housing off the dowels and remove it. The weight of the flywheel housing is 191 kg (425 lb).13. Put the flywheel housing in the position shown. 14. Remove bolts (17) from shafts (19).
Bearings (20) can fall out of gears (18) when the gears are removed from the flywheel housing.
15. Remove gears (18) from the flywheel housing. 16. Remove shafts (19), bearing cones (22), spacers (21) and bearing cones (20) from gears (18). 17. If necessary, remove bearing cups (23) and (25), spacers (24) and the snap rings from gears (18). The bearing cups will have damage after removal. Use new parts for replacement.Install Flywheel Housing
1. Install the snap rings in the groove in idler gear (2).2. Install the spacers for bearing cups (1) in gears (2) from the side of gears (2) that have the part number. Make sure the notches in the spacers are toward the snap rings. The snap rings are not in the center of the gear bores. The spacers must be installed in the gear bores that have the longer measurement from the snap ring to the surface of the gear.3. Lower the temperature of bearing cups (1) and install them in gears (2) until they make contact with the spacers. 4. Put the flywheel housing in the position shown and install bearing cones (3). 5. Put idler gears (2) in position on the bearing cones. Make sure the side of gears (2) with the part number is toward the flywheel housing. 6. Put spacer (4) on the inner race of the bearing cone. 7. Install bearing cones (5) in the gears. 8. Install shafts (6) and the bolts to hold them.
Put the No. 1 piston at top center to make an alignment of the timing marks on the crankshaft rear gear (9) with the balancer gear (8). Failure to follow this procedure can cause damage to the engine.
9. Clean the front face of the flywheel housing and the rear face of the cylinder block. Make an application of 20 ml (.7 oz) of 6V-6640 Bulk Gasket as a (continuous) line inside the center line of the holes in the flywheel housing. Remove excess gasket material. 10. Use Tooling (A) and fasten a hoist to flywheel housing (7). Make an alignment of the timing marks on the crankshaft rear gear (9) and the balancer gear (8). 11. Tighten the flywheel housing bolts as follows:a. Tighten bolts 1 through 8 in number sequence shown to a torque of 135 14 N m (100 10 lb ft).b. Tighten bolts 1 through 21 in number sequence shown to a torque of 54 7 N m (40 5 lb ft).c. Tighten bolts 1 through 8 again in number sequence shown to a torque of 135 14 N m (100 10 lb ft).d. Tighten bolts 9 through 21 again in number sequence shown to a torque of 54 7 (40 5 lb ft). 10. Put bracket (10) in position and install the bolts through the lower section of the turbocharger heat shield. 11. Install plate (11). 12. Install drain line (12) and elbow (13). 13. Install the top section of turbocharger heat shield (14). 14. Install bracket (15) and turbocharger oil return line (16). 15. Install engine rear supports (17). 16. Connect oil supply line (18) to the flywheel housing and install starting motor (19). 17. Install cover (21) with a new O-ring seal (20). 18. Install pump drives (23) (if equipped) and plates (22). 19. Install implement pump (24) (if equipped).End By:a. install oil panb. remove crankshaft rear seal and wear sleeve


Parts tapered Mercruiser:

852066
 
852066 TAPERED ROLLER BEARING (INNER)
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813311
813323
TAPERED ROLLER BEARING (INNER)
813323 TAPERED ROLLER BEARING (INNER)
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813324
 
813324 TAPERED ROLLER BEARING (OUTER)
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813325
TAPERED ROLLER BEARING (INNER)
813325 TAPERED ROLLER BEARING (INNER)
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813326
 
813326 TAPERED ROLLER BEARING (OUTER)
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813331
 
813331 TAPERED ROLLER BEARING
428B116KD, 442B110GD, 442B115KD, 4A72040ND
811985
 
811985 TAPERED ROLLER BEARING
428B116KD, 442B110GD, 442B115KD, 4A72040ND
Back to top