802556 Mercruiser CYLINDER HEAD ASSEMBLY, Cylinder


802556 CYLINDER HEAD ASSEMBLY, Cylinder Mercruiser 40500006T, 40500010T, 40500010U, 40500120U, 4332087N1, 444106LPS, 444236HRS, 4M11025LS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M31027LS, 4M4102LPS, 4M4102LRS, 4M4102LTS CYLINDER
802556 CYLINDER HEAD ASSEMBLY, Cylinder Mercruiser
Rating:
68

Buy CYLINDER HEAD ASSEMBLY, Cylinder 802556 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$449.95
 

29-08-2024
51.0[22.95] pounds
US: Center State Marine
5.0L GM Vortec Marine Engine Cylinder Head. Replaces Mercruiser & Volvo Penta applications years 1997-newer. Replaces Mercruiser 938-8M0087884
Marine Engines 4 Less New aftermarket complete cylinder head with valves and springs. || Replaces Mercruiser Volvo Penta, OMC, Marine Power, GM Marine 5.0L years 1997-newer. || Replaces Mercruiser part numbers 938-8M0087884, 802556 || Replaces Volvo Penta part number 3857663 || Replaces GM part number 12558059
Number on catalog scheme: 22
 

Mercruiser entire parts catalog list:

40500006T 1998
40500010T 1998
40500010U 1998
40500120U 1998
4332087N1 1998
444106LPS 1998
444236HRS 1998
4M11025LS 1998
4M11025RS 1998
4M11025TS 1998
4M11025TT 1998
4M11025US 1998
4M31027LS 1998
4M4102LPS 1998
4M4102LRS 1998
4M4102LTS 1998

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging the hoses helps to prevent fluid loss and prevents contaminants from entering the system.
If the alternator bracket is mounted on the cylinder head, remove the alternator. Refer to Disassembly and Assembly, " Alternator - Remove".
If the fuel priming pump and the primary fuel filter are mounted on the cylinder head, remove the fuel priming pump and the primary fuel filter. Refer to Disassembly and Assembly, "Fuel Priming Pump - Remove and Install".
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g01245537
Typical example
Disconnect the upper radiator hose from water temperature regulator housing (1).
If necessary, remove the air hose from the inlet connection.
Follow Step 6.a and Step 6.b in order to disconnect harness assembly (4) from coolant temperature sensor (2).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from coolant temperature sensor (2).
If necessary, follow Step 7.a and Step 7.b in order to disconnect harness assembly (4) from boost pressure sensor (3).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from boost pressure sensor (3).
Illustration 2 g01249835
Typical example
Follow Step 8.a and Step 8.b in order to disconnect harness assembly (4) from inlet air temperature sensor (5).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from inlet air temperature sensor (5).
Remove all cable straps that secure harness assembly (4) to the cylinder head. The harness assembly should be positioned in order to avoid causing an obstruction during the removal of the cylinder head.
Illustration 3 g03684268
Typical example
Remove tube assembly (6) from the cylinder head and from transfer pump (7).
Illustration 4 g01249479
Typical example
If the engine is equipped with a wastegate solenoid, remove harness assembly (9) from tube assembly (8). Remove the bolts for tube clip (10) and tube clip (11). Remove tube assembly (8) from the wastegate solenoid and from the cylinder head.
Illustration 5 g01476537
Typical example
Remove bolts (12). Note the position of any brackets that are secured by the bolts. Remove bypass tube (13) from the cylinder head. Remove O-ring seals (14) and (15) from the bypass tube.
Illustration 6 g01245538
Illustration 7 g01250785
Sequence for loosening the bolts for the cylinder head
Gradually loosen bolts (16) in the reverse numerical order to the sequence that is shown in Illustration 7. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolts (16) from cylinder head (17).
Attach a suitable lifting device to cylinder head (17). Support the weight of the cylinder head. The weight of the cylinder head is approximately 56 kg (124 lb).
Use the suitable lifting device to carefully lift cylinder head (17) off the cylinder block. Note: Do not use a lever to separate the cylinder head from the cylinder block. Take care not to damage the machined surfaces of the cylinder head during the removal procedure.
Place the cylinder head on a surface that will not scratch the face of the cylinder head.


Parts cylinder Mercruiser:

9718 1
 
9718 1 CYLINDER HEAD ASSEMBLY
4350104JS, 4350104KS, 4350118JS, 4350118KS, 4441027LE, 444106AM1, 4M31027LS
803860T
CYLINDER HEAD ASSEMBLY, Cylinder
803860T CYLINDER HEAD ASSEMBLY, Cylinder
40500006T, 40500010T, 40500010U, 40500120U, 4332087N1, 4441027LE, 444106LPS, 444236HRS, 4M11025LS, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M31027LS, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4R42027N1
879172A32
 
879172A32 CYLINDER HEAD ASSEMBLY
40500010U, 40500120U
Back to top