806952 DECAL Mercruiser
4350111HS, 4350118JS
DECAL
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$19.95
21-08-2024
2.0[0.90] pounds
US: Race-Driven Inc
Sprocket fits Honda ATC200X 1983 1984 1985 Rear 40 Tooth by Race-Driven
Race-Driven Brand New 40 Tooth Rear Steel Sprocket || Race-Driven sprockets are manufactured to exceed OEM specifications || Race-driven sprockets are produced using hardened S45C steel || Fits: 1983 1984 1985 Honda ATC200X
Race-Driven Brand New 40 Tooth Rear Steel Sprocket || Race-Driven sprockets are manufactured to exceed OEM specifications || Race-driven sprockets are produced using hardened S45C steel || Fits: 1983 1984 1985 Honda ATC200X
$38.86
07-10-2017
Needa Part: Needa Parts
Needa Parts 806952 Front Left Black Exterior Door Handle with Key Hole
Meets or exceeds OEM standards||Outside Door Handle||Finish: Black; Paint To Match
Meets or exceeds OEM standards||Outside Door Handle||Finish: Black; Paint To Match
Number on catalog scheme: 4
Mercruiser entire parts catalog list:
- INTAKE PLENUM AND FLAME ARRESTOR » 806952
- INTAKE PLENUM AND FLAME ARRESTOR » 806952
Information:
1. Remove shaft (2). Remove pin (1) from shaft.2. Remove pins (3) from the flyweights. Remove flyweights (4). 3. Remove ring, races (6) and bearing from the riser (follower) (5). 4. Remove cover (7) and spring (8) from governor housing. There is force on the cover from the spring.5. Remove seal (9) from cover.6. Remove cover (10) for the low and high idle adjustment. 7. Remove locknut and screw (13) for the high idle adjustment.8. Remove bolt (15) and washers for the low idle adjustment.9. Remove spring (16) and guide.10. Remove pin (14) and plate (11).11. Remove shaft (12) from the housing. 12. Remove pin (18) and two spacers (17) from shaft. Earlier fuel systems have a ball in place of spacers (17) and pin (18). 13. Remove shaft (19) from the governor housing.14. Remove washer (20) and levers (21) and (22) from governor housing. 15. Remove cover (23) from governor housing. 16. Remove seal (25) and bearing.17. Remove seals (24) and 26) from governor housing.Assemble Governor
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A 10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.END BY:a) connection of governor to fuel injection pump housing
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A 10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.END BY:a) connection of governor to fuel injection pump housing
Parts decal Mercruiser:
805364A 1
805364A 1 DECAL SET (COLOR CODE)
02602347, 02608427, 257B021JS, 40430002S, 4111021L1, 411102KN2, 4211015L1, 4231017L1, 424106LRS, 4262C01JT, 430L000JS, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 444106LPS, 444236HRS,