816610A 1 Mercruiser DIPSTICK ASSEMBLY


816610A 1 DIPSTICK ASSEMBLY Mercruiser 5000150DP, 5000165CE DIPSTICK
816610A 1 DIPSTICK ASSEMBLY Mercruiser
Rating:
18

Buy DIPSTICK ASSEMBLY 816610A 1 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$9.90

15-06-2025

CN: GlückMarine
GlückMarine 79953 2 Pcs Boat Gear Case Drain Screws with Seals for Mercury Marine Outboard and MerCruiser Stern Drive replace 10-79953 10-79953A2 Lower Unit Oil Drain Plugs
GluckMarine These non-magnetic drain screws with washers are used with 3/8-16 drain and fill hole screw on all Mercruiser out drives, Mercury and Mariner outboards EXCEPT the Verado series || Compatible with Mercury/MerCruiser 10-20259 10-28634 10-28634A1 10-79953 10-79953A2 10-79953Q04 10-79953Q2 816610A1 816610A2 || Also replace GLM 22420, Mallory 9-72650 and Sierra 18-2244 18-22441-9 || The outdrive gearcase drain plug is made of stainless steel and can help prevent gear lube from leaking out and water from seeping in to the gear housing causing serious damage || Package contains: 2 pcs drain screws and 6 pcs drain screw gaskets, extra gaskets save you both time and money
$25.99

24-05-2025

US: tzdz
Lower Unit Gear Oil Pump and 18-2244 Drain Plug Screw & Gasket Kit for Mercury/Mercruiser 1/MR/R/Alpha/Alpha I Gen II
Generic 18-2244 Drain Plug Screw & Gasket Kit Lower Unit Gear Oil Pump Fits for Mercury/Mercruiser #1/MR/R/Alpha/Alpha I Gen II Upper & Lower Units || Replaces Part # 816610A1 816610A2 10-F50109 F40109 10-79953 9-72650 10-28634 10-79953Q04 10-79953Q2 || Marine Drain Plug, gasket, washer Replace For MerCruiser I,R,MR,Alpha One,TR,TRS & all O/Bs with 3/8-16 non-magnetic gear lube fill or vent screws || Lower Unit Gear Oil Pump includes 3 adapter sizes. 3/8"(Swivel, Metal), 8mm and 10mm (Metal). Take the guess work out of figuring out the size of your Lower Unit's gear oil drain plug. (WON'T FIT VOLVO PENTA) Fit all tall or short Quart Bottles, perfectly used on 32 ounce (946 ml) Gear Lube Bottle. || Comes with 2 suction tubes which can reach the bottle bottom of tall and short gear oil bottles. 8 cc stable current per stroke. Easy to use. All the adapters are made of strengthen steel with zinc plated. Skip the plastic made adapters and use this ultimate kit, they are great to reuse for many times.
$7.99

15-06-2025

CN: UTSAUTO
UTSAUTO Marine Drain Plug Screw 79953Q04 Lower Unit Oil Drain Plug Screw Fit for Mercury MERCRUISER 10-79953Q2 10-79953A2 18-2244 22420 816610A1 28634 79953 2pc Screw with 4pcs gasket
UTSAUTO Replacement number: 79953Q04 10-79953Q2 10-79953A2 18-2244 22420 816610A1 28634 79953 || UTSAUTO Marine drain plug made with high quality material,ensure long term use with no cracked. || Easy to replace, just replace the original drain plug directly. || Lower unit Drain Plug kit used with 3/8 - 16 drain or fill hole screw of all for MerCruiser stern drives, Mercury and Mariner outboards EXCEPT The VERADO series || Package include 2pcs Marine drain plug and 4pcs gaskets
Number on catalog scheme: 6
 

Compatible models:

5000150DP   5000165CE   Mercruiser

Mercruiser entire parts catalog list:

5000150DP 1991,1992,1993,1994,1995
5000165CE 1990,1991

Information:

1. Remove the bolts and the plate from the side of the fuel injection pump housing.2. Install Tool (A) in the fuel injection pump housing. Move the rack until Tool (A) can be installed to hold the rack in the center position. The rack must be in the center position to remove the fuel injection pumps.3. Use Tool (B) to remove bushing (1) from the fuel injection pump housing.4. Remove the O-ring seal from the fuel injection pump housing. Spacers (2) are the same thickness for each fuel injection pump so they can be mixed. The fuel injection pump plungers and barrels are sets and can not be mixed.5. Install Tool (C) on the bonnet, and remove the fuel injection pump. 6. Remove spacer (2) from the fuel injection pump housing.7. Do Steps 3 through 6 to remove the other fuel injection pumps.Install Fuel Injection Pumps
1. Install spacer (1) in the fuel injection pump housing. 2. Install Tool (A) in the fuel injection pump housing. Move the rack until Tool (A) can be installed to hold the rack in the center position. The rack must be in the center position to install the fuel injection pumps.3. Turn the camshaft until the lobe of the camshaft is down for the pump to be installed.4. Install Tool (B) on the bonnet of the fuel injection pump.5. Install the fuel injection pump in the pump housing with saw cut (slot) (3) in the gear in alignment with the small pin (2) and groove (4) in the barrel in alignment with dowel (5) in the pump housing. 6. Put clean oil on O-ring seal (6), and install it in the fuel injection pump housing.7. Install the bushing by hand until it is even with the top of the housing. If the bushing can not be installed this far by hand, remove it. Remove the fuel injection pump, and put the pump in alignment again, and install the bushing again. 8. Install Tool (C) on the bushing and tighten the bushing to a torque of 163 14 N m (120 10 lb ft). 9. Install Tooling (D) to measure total rack travel. Correct rack travel is 15.70 mm (.618 in). A smaller measurement is an indication of incorrect fuel injection pump installation.10. Do Steps 1 through 9 again for installation of the other fuel pumps.11. Install the cover and gasket on the fuel injection pump housing.End By:a. install governorDisassemble Fuel Injection Pumps
Start By:a. remove fuel injection pumps FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates.
Be careful when the injection pumps are disassembled. Do not damage the surfaces of the plungers, barrels and bonnets. Any scratches will cause leakage inside the fuel injection pump. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
1. Pull plunger (1) and washer (5) out of barrel (3) and spring (2).2. Remove washer (5) from plunger (1).
Do not remove the gear from the plunger. The gear and plunger are assembled and adjusted at the factory.
3. Remove spring (2) from barrel (3).4. Remove ring (6), and separate barrel (3) and bonnet (4). 5. Remove check assembly (7) and spring (8) from bonnet (4). If check assembly (7) is disassembled, do not mix parts with parts from another check assembly.Assemble Fuel Injection Pumps
Put clean fuel oil on all parts during assembly.
1. Install spring (2) and check assembly (1) in bonnet (3). 2. Install bonnet (3) on barrel (4). Install ring (5) to hold them together.
Do not slide bonnet (3) across barrel (4) because check assembly (1) in the bonnet can damage the face of barrel (4).
3. Install spring (8) on barrel (4).4. Install washer (7) on plunger (6) with the flat side toward the gear on the plunger.5. Install plunger (6) in barrel (4) until washer (7) is engaged in the spring.End By:a. install fuel injection pumps


Parts dipstick Mercruiser:

41218
 
41218 DIPSTICK
00019003, 01321017, 01326013, 03301310, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5220200AS, 5231100LP, 5C30150FS, 6020006JS, 6211001N1, 6311002NZ, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
Back to top