818390 DRAIN COCK Mercruiser
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M11025LS, 4M4102LPS, 4M4102LRS, 4M4102LTS
DRAIN
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$42.49
07-10-2017
HODELL-NAT: HODELL-NATCO INDUSTR
Universal 818390 Machine Screw, 1/4-20 x 3/4" Phillips Head (Pack of 100)
Phillips Flat Machine Screws Zinc: A countersunk head with a flat top surface with a head angle of approximately 82 degrees||Used in applications where protrusion of the fastener above the mating surface is unacceptable||Phillips drive provides good control during installation
Phillips Flat Machine Screws Zinc: A countersunk head with a flat top surface with a head angle of approximately 82 degrees||Used in applications where protrusion of the fastener above the mating surface is unacceptable||Phillips drive provides good control during installation
Compatible models:
Mercruiser entire parts catalog list:
- THERMOSTAT AND HOUSING(EASY DRAIN) » 818390
40500010T 1998
40500010U 1998
40500120U 1998
4211025RS 1998
- THERMOSTAT AND HOUSING » 818390
- THERMOSTAT AND HOUSING » 818390
- THERMOSTAT AND HOUSING » 818390
- THERMOSTAT AND HOUSING » 818390
- THERMOSTAT AND HOUSING » 818390
424106LTT 1998
424106LUS 1998
- THERMOSTAT AND HOUSING, SINGLE AND 3 POINT DRAIN » 818390
- THERMOSTAT AND HOUSING(SINGLE AND 3 POINT DRAIN) » 818390
444106LPS 1998
- THERMOSTAT AND HOUSING(EASY DRAIN) » 818390
- THERMOSTAT AND HOUSING(SINGLE AND 3 POINT DRAIN) » 818390
- THERMOSTAT AND HOUSING(EASY DRAIN) » 818390
- CLOSED COOLING SYSTEM » 818390
- THERMOSTAT AND HOUSING(EASY DRAIN) » 818390
4M4102LTS 1998
Information:
Table 1
Customer Name/ Location     Machine Unit Number     Machine Serial Number     Machine Service Meter Hours     Work Order Number    
/                    
Table 2
Tracking Data     Engine Removed     Engine Installed     T/C Removed     T/C Installed    
Serial Number                    
CID Number (1)                    
Source/Rebuilder (2)                    
( 1 ) CID (Component Identification) is the number assigned to the component by the user/dealer.
( 2 ) Suorce/Rebuilder is either NEW, REMAN, DLR (Dealer Rebuilt), or CUST (Customer Rebuilt).Checklist
Table 3
1.         Record Complaint:        
           
   
2.         Pre-repair contamination control.    
        A.     High-pressure wash the rear half of the truck to remove all dirt/debris.    
        B.     Keep the work area clean and the floor dry - contain all fluid spills.    
        C.     Cover components with plastic or keep in containers until installation to keep clean.    
        D.     Verify new parts cleanliness. Assure that they are cleaned and capped/ protected against dirt.    
   
3.         Investigate engine and torque converter history or failure cause, if appropriate.    
        A.     Question the operator on application, operating conditions, and history. Review SOS history.    
        B.     Review VIMS and EPTC2 for detected fault information - record the work order folder.    
        C.     Take SOS Sample refer to: Contamination Control Guidelines, SEBF8482, "Obtaining Oil Sample for Analysis". Drain the engine and related power train oil reservoirs and visually check oil for water, coolant, or debris contaminants.    
        D.     Remove/inspect system filters/screens and save any contamination evidence.    
   
4.         Clean engine compartment with high-pressure wash before and after engine removal.    
   
5.         Cover and cap all cleaned and reused components/lines until installed to prevent dirt entry.
Cover all removed component cores with plastic sheets until shipping covers are available.    
   
6.         Inspect engine mounts and machine frame for stripped threads, cracks, or deformation. Repair/replace and paint as needed.    
   
7.         Inspect and clean or replace system hoses/tubes. Clean with Cat hose cleaner group. Refer to Reuse and Salvage Guidelines, NEHS0643 and Reuse and Salvage Guidelines, SEBF8485. Use new clamps (torque to spec), O-ring seals, and gaskets.    
   
8.         Inspect/replace electrical connectors and harnesses for loose pins, brittleness, and fatigue. Replace the engine wire harness every rebuild life cycle.    
   
9.         Install cleaned/repaired or new radiator cores. Perform hydraulic fan drive system calibration.    
   
10.         Clean/protect pump drive mounting surfaces and exposed cavities of the replacement components.    
   
11.         Install rebuilt/new pump drive coupling.    
   
12.         Clean/protect all mounting surfaces and exposed cavities of the replacement components.    
   
13.         Transfer all covers/plugs to the removed component cores and pack into shipping containers to prevent damage and dirt entry. Tag with completed Caterpillar dealer core tag.    
   
14.         Clean/replace the primary air filters. Replace the secondary air filters. Clean the pre-cleaners. Reset air filter restriction indicator. Insure air induction system integrity (before turbocharger).    
   
15.         Prelube the engine with oil meeting ISO --/16/13 cleanliness level and prime the fuel system before starting.    
   
16.         Check engine s
Parts drain Mercruiser:
809911
809911 DRAIN SCREW
257B021JS, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 4454110JT, 4454118JT, 4542067LS, 457B100KS, 457B101JS, 457B101KS, 457L101JS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JT, 4M11025L
863381A 1
863381A 1 DRAIN ROD ASSEMBLY
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS