97006 Mercruiser ELBOW, OIL PAN


97006 ELBOW, OIL PAN Mercruiser 04707333, 04708004, 04881333 ELBOW
97006 ELBOW, OIL PAN Mercruiser
Rating:
83

Buy ELBOW, OIL PAN 97006 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 30
 

Compatible models:

Mercruiser entire parts catalog list:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B - Guide Stud
5/8 - 18 by 12 inch 1
C - Loctite™536 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Apply clean engine oil to the bearings and the shaft assemblies prior to installation on the engine.
Illustration 1 g01219500
Install the O-ring seals and the sealing plates on the cylinder head.
Install adapter assemblies (15), thrust plates (14), and bolts (13).
Position shaft assembly (17) and install bolts (16).
Tighten bolts (16) to a torque of 135 20 N m (100 15 lb ft).
Illustration 2 g02090315
Illustration 3 g02087895
(X) Marker
(Y) Alignment Mark
Illustration 4 g02088394Note: Align the Timing Marks on gear assemblies (4) with the Timing Marks on the rear housing and align the dowels on gear assemblies (4) with the adapter assemblies.
Position gear assemblies (4) and loosely install bolts (5).
Apply Tooling (C) to the shaft and install Tooling (B) in the crankshaft. Install gear assembly (12).
If the top center position is already marked on the vibration damper, proceed to Step 7.
Install the flywheel housing and the flywheel temporarily. Two bolts in the flywheel housing and the flywheel are sufficient.
Position the number one piston in the top center position (TC). The engine should be at the top center position to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
With the number one piston in the top center position (TC), attach a marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel and the flywheel housing.
Install two nuts on two bolts for the flywheel (18). The nuts will provide spacing when the bolts are installed. Install two bolts for the flywheel (18) in gear assembly (12).
Use Tooling (A) and a suitable press to install the bearing in gear assembly (1). Install the bearing to a depth of 2.6 0.5 mm (0.10 0.02 inch).
Install shaft assembly (3), gear assembly (1), and bolts (2).
Tighten bolts (2) to a torque of 55 10 N m (41 7 lb ft).
Use Tooling (A) and a suitable press to install the bearing in gear assembly (6). Install the bearing to a depth of 2.6 0.5 mm (0.1 0.02 inch).
Install shaft assembly (7), gear assembly (6), and bolts (8).
Tighten bolts (8) to a torque of 55 10 N m (41 7 lb ft).
Use Tooling (A) and a suitable press to install the bearing in gear assembly (9). Install the bearing to a depth of 2.5 0.5 mm (0.1 0.02 inch).Note: Ensure that the number one piston is in the top center position (TC). Ensure that the timing marks on gear assemblies (4) are in alignment with the timing marks on the rear housing.
Hold gear assembly (6) in the direction of normal engine rotation to remove the backlash. Place gear assembly (9) on the shaft assembly. The teeth on gear assembly (9) will engage with gear assembly (12) first. The teeth on gear assembly (9) will engage with the teeth on gear assembly (6) next. If the teeth on gear assembly (9) do not engage properly, turn the gear assembly to the next tooth and try again.
Install thrust plate (11) and bolts (10).
Tighten bolts (8) to a torque of 55 10 N m (41 7 lb ft).
Turn the engine in the opposite direction of normal engine rotation for approximately 45 degrees. Turn the engine in the direction of normal engine rotation until the alignment mark on the vibration damper and the marker on the engine are aligned. Ensure that timing marks on gear assemblies (4) are in alignment with the marks on the rear housing.
Illustration 5 g01151468
Tighten bolts (5) on gear assemblies (4) to a torque of 240 40 N m (177 30 lb ft). Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4 as shown above.End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".


Parts elbow Mercruiser:

37760
 
37760 ELBOW, OIL COOLER
01206002, 01207333, 01326013, 01406002, 01407333, 01851333, 02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 08986342, 228801, 260801
47625
 
47625 ELBOW, OIL LEVEL GAUGE TO OIL PAN INBOARD
02287333, 02297343, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04856332, 08986342, 228801, 4454110AS, 474H110AR
36305
 
36305 ELBOW, EXHAUST RISER
00014332, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 06661346, 07711346, 08986342, 08987343, 228801, 30001854, 32001876, 37
47629
 
47629 ELBOW, HOSE TO TRANSMISSION (90 DEGREE)
02287333, 02297343, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 08986342, 228801, 30001854, 37011856, 44031854, 473B1F0GS, 4V71222PD, 4V71222TD
63835
 
63835 ELBOW, HOSE TO TRANSMISSION (45 DEGREE)
02287333, 02297343, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 08986342, 228801, 37011856, 428B116KD, 442B110GD, 442B115KD, 4441027LE, 444106AM1, 473B1F0GS, 4A72040ND, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M31027LS
72082A 2
74033
 
74033 ELBOW,OVERFLOW
04706002, 04707333, 04708004, 04856332
76170
 
76170 ELBOW,RESERVOIR BY-PASS
01701335, 04706002, 04707333, 04708004, 04856332, 04881333
Back to top