865461 Mercruiser FILTER


865461 FILTER Mercruiser 41000001S, 41000008E FILTER
865461 FILTER Mercruiser
Rating:
58

Buy FILTER 865461 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Compatible models:

41000001S   41000008E   Mercruiser

Mercruiser entire parts catalog list:

41000001S 1998
41000008E 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank As 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The following steps are for the installation of a camshaft in the 3512B Engines and 3516B Engines. The camshaft is in two pieces.Note: Ensure that the camshafts are assembled and installed according to the marks on the ends of the camshafts.
Illustration 1 g01053512
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the end of the front half of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Attach a suitable lifting device to the camshaft. The weight of one-half of the camshaft for 3512B Engines is approximately 36 kg (80 lb). The weight of one-half of the camshaft for 3516B Engines is approximately 41 kg (90 lb).
Position the front half of camshaft (12) in the engine until Tooling (C) is in the first camshaft bearing.
Rotate camshaft (12) and tighten the bolts for Tooling (D).
Rotate camshaft (12) and insert the camshaft until the camshaft is slightly protruding from Tooling (D).
Illustration 2 g00914670
Illustration 3 g00914462
If the dowel was removed from the front half of camshaft (12), install the dowel. Install the dowel to 22 0.5 mm (0.9 0.02 inch) from the surface of the camshaft.
Attach a suitable lifting device to rear half of camshaft (13). The weight of one-half of the camshaft for 3512B Engines is approximately 36 kg (80 lb). The weight of one-half of the camshaft for 3516B Engines is approximately 41 kg (90 lb). Install spacer (15) and the rear half of camshaft (13) onto the front half of camshaft (12). Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).
Install Tooling (C) and Tooling (E) on the rear half of camshaft (13).
Rotate the rear half of camshaft (13) and insert the camshaft into the engine.
Remove all Tooling. Repeat Steps 1.a through 1.k for the camshaft on the opposite side of the engine. Go to Step 3.
The following steps are for the installation of the camshaft in 3508B Engines. The camshaft is one piece.
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the end of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.Note: Ensure that the camshafts are installed according to the marks on the ends of the camshafts.
Attach a suitable lifting device to the camshaft. The weight of the camshaft is approximately 46 kg (101 lb). Insert the camshaft in the engine until Tooling (C) is in the first camshaft bearing.
Install Tooling (E). Rotate the camshaft and tighten the bolts on Tooling (D).
Rotate the camshaft and insert the camshaft into the engine.
Repeat Steps 2.a through 2.f for the camshaft on the opposite side of the engine. Go to Step 3.
Illustration 4 g00914691
Install thrust washers (10). Install bolts and washers (9) that fasten the camshaft to the engine.
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 5 g00914693
Remove timing pin (16) from the storage position on the side of the engine.
Turn the camshaft until timing pin (16) can be installed through the cylinder block and into groove (17) that is in the camshaft.
Repeat Steps 4 and 5 for the camshaft on the opposite side of the engine.
Illustration 6 g00914707


Parts filter Mercruiser:

866594K01
 
866594K01 FILTER, Fuel - Spin On
41000001S, 41000008E, 41510P1UE
866340K01
FILTER, Oil - Mercury Brand
866340K01 FILTER, Oil - Mercury Brand
40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021UT, 4111021UU, 41510P1UE, 4211025US, 4211025UU, 424106LUS, 424106PUU, 4M11025US, 4S42028UT, 4S42028UU, 4S420P8UE
Back to top