70584 FITTING, FUEL LINE Mercruiser
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04856332, 2165203, 2165208
FITTING
Price: query
Rating:
Compatible models:
Mercruiser entire parts catalog list:
01207333 1983
01326013 1983
01406002 1982
01407333 1983
04706002 1982,1983
- CARBURETOR AND FUEL PUMP » 70584
- CARBURETOR AND FUEL PUMP » 70584
2165203 1973,1974,1975,1976,1977
- FUEL PUMP AND CARBURETOR » 70584
- FUEL PUMP AND CARBURETOR » 70584
Information:
Introduction
With the release of Tier 4 Final engines, additional emissions control system components have been added to the engine to reduce the NOx output. The addition of these components requires three Electronic Control Modules (ECMs) for the engine and aftertreatment systems to operate. The most recent version of Cat® Electronic Technician (ET) must be used when connecting the engine.When the controllers are flashed, the computer and Comm Adapter 3 that will be used to flash the controllers on the engine must be set up properly in order to avoid issues caused by a failed flash file installation. The purpose of this special instruction is to show how the power settings for both the Comm Adapter 3 and the computer must be set up in order to avoid a flashing issue.Computer Settings
Turn off Power Management of USB Root Hubs.
Windows can sometimes power down USB devices when the PC enters standby mode, even if the USB devices are in use. For instance, during a long ECM flash programming operation if the screen saver engages, Windows may turn off the power to the CA3 USB port and interrupt the flash causing the flash to fail.In order to eliminate this problem, it is recommended that the power management on the USB root hubs is disabled.
Illustration 1 g03354796
On Windows XP machines, click the start button and Select "Run". On Windows 7 machines, use the "Search Programs and Files" search box at the bottom of the start menu. Type "Devmgmt.msc" into the box and press "Enter".
Illustration 2 g03354797
Expand the "Universal Serial Bus controllers" tab.
Right click a "USB Root Hub" in the list, and then click "Properties". The "USB Root Hub Properties" dialog box is displayed.
Click the "Power Management" tab.
Illustration 3 g03354798
Uncheck the box next to "Allow the computer to turn off this device to save power", and then click "OK".
Repeat steps 1 through 5 for each "USB Root Hub" in the list.
On the Action menu, click "Scan for hardware changes".
Close the "Device Management" window.Firmware
Illustration 4 g03360527To check the current version of firmware that is currently in the Comm Adapter 3:
Plug the Comm Adapter 3 into the USB port on the computer and make sure that the adapter is powered on.
In Cat® ET 2013A or newer, select the "Communications Adapter 3 Toolkit" from the "Utilities" menu.
Check the "Software Release Version".
If the "Software Release Version" is not 1.18.47 or newer, the firmware within the Comm Adapter 3 will have to be updated.
Illustration 5 g03485341
Illustration 6 g03485343
Select "Application Firmware Flash" from the menu and click on "Select File". This will bring up the directory where the firmware is located.
Illustration 7 g03485359
Illustration 8 g03485376
Select the most up-to-date firmware and click on the "Open" button. Then click the "Begin" button at the bottom of the "Application Firmware Flash" screen.Starting with Cat® ET 2013A the most up-to-date Comm Adapter 3 firmware is included with each version of Cat® ET.Power Toggle
When using the Comm adapter 3 normally, power is received from both the nine pin connector and from the USB port on the computer. Using the Comm adapter 3 normally can cause electrical interference when sending a flash file. Using the power toggle allows the user to turn off the power coming from the USB port to minimize the electrical interference. After this procedure is performed, the Comm adapter 3 will only turn on when connected to machine power. The power supply from the USB to the Comm adapter 3 can be turned back on if needed.
Plug the Communications Adapter 3 into the USB port on the computer and make sure that the adapter is powered on.
In Cat® ET 2013A or newer, select the "Communications Adapter 3 Toolkit" from the "Utilities" menu.
With the release of Tier 4 Final engines, additional emissions control system components have been added to the engine to reduce the NOx output. The addition of these components requires three Electronic Control Modules (ECMs) for the engine and aftertreatment systems to operate. The most recent version of Cat® Electronic Technician (ET) must be used when connecting the engine.When the controllers are flashed, the computer and Comm Adapter 3 that will be used to flash the controllers on the engine must be set up properly in order to avoid issues caused by a failed flash file installation. The purpose of this special instruction is to show how the power settings for both the Comm Adapter 3 and the computer must be set up in order to avoid a flashing issue.Computer Settings
Turn off Power Management of USB Root Hubs.
Windows can sometimes power down USB devices when the PC enters standby mode, even if the USB devices are in use. For instance, during a long ECM flash programming operation if the screen saver engages, Windows may turn off the power to the CA3 USB port and interrupt the flash causing the flash to fail.In order to eliminate this problem, it is recommended that the power management on the USB root hubs is disabled.
Illustration 1 g03354796
On Windows XP machines, click the start button and Select "Run". On Windows 7 machines, use the "Search Programs and Files" search box at the bottom of the start menu. Type "Devmgmt.msc" into the box and press "Enter".
Illustration 2 g03354797
Expand the "Universal Serial Bus controllers" tab.
Right click a "USB Root Hub" in the list, and then click "Properties". The "USB Root Hub Properties" dialog box is displayed.
Click the "Power Management" tab.
Illustration 3 g03354798
Uncheck the box next to "Allow the computer to turn off this device to save power", and then click "OK".
Repeat steps 1 through 5 for each "USB Root Hub" in the list.
On the Action menu, click "Scan for hardware changes".
Close the "Device Management" window.Firmware
Illustration 4 g03360527To check the current version of firmware that is currently in the Comm Adapter 3:
Plug the Comm Adapter 3 into the USB port on the computer and make sure that the adapter is powered on.
In Cat® ET 2013A or newer, select the "Communications Adapter 3 Toolkit" from the "Utilities" menu.
Check the "Software Release Version".
If the "Software Release Version" is not 1.18.47 or newer, the firmware within the Comm Adapter 3 will have to be updated.
Illustration 5 g03485341
Illustration 6 g03485343
Select "Application Firmware Flash" from the menu and click on "Select File". This will bring up the directory where the firmware is located.
Illustration 7 g03485359
Illustration 8 g03485376
Select the most up-to-date firmware and click on the "Open" button. Then click the "Begin" button at the bottom of the "Application Firmware Flash" screen.Starting with Cat® ET 2013A the most up-to-date Comm Adapter 3 firmware is included with each version of Cat® ET.Power Toggle
When using the Comm adapter 3 normally, power is received from both the nine pin connector and from the USB port on the computer. Using the Comm adapter 3 normally can cause electrical interference when sending a flash file. Using the power toggle allows the user to turn off the power coming from the USB port to minimize the electrical interference. After this procedure is performed, the Comm adapter 3 will only turn on when connected to machine power. The power supply from the USB to the Comm adapter 3 can be turned back on if needed.
Plug the Communications Adapter 3 into the USB port on the computer and make sure that the adapter is powered on.
In Cat® ET 2013A or newer, select the "Communications Adapter 3 Toolkit" from the "Utilities" menu.
Parts fitting Mercruiser:
64425
64425 FITTING, DRAIN COCK EXTENSION
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208
45370
49217
64294
29085
29085 FITTING, OIL PRESSURE SENDER ADAPTOR
2165203, 2165208, 4231017L1, 4454110JT, 4454118JT, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 473B1F0GS, 474L111JS, 474L118JS, 474L118JT, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
42897
42897 FITTING, ELBOW-FUEL PUMP
01701335, 04707333, 04708004, 44541101S, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 474L118JS, 474L118JT
42861 1
42861 1 FITTING, Pipe - Brass (.750-14)
00019003, 01321017, 01326013, 01701335, 40200002D, 40200002G, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 4
67892A 1
67892A 1 FITTING KIT, Magnetic, Plug Fill/Drain
00019003, 01321017, 01326013, 5000147JS, 5000165CE, 5111200LP, 5120136JS, 5120150R1, 5220200AS, 5231100LP, 5232100N1, 5C30150FS, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS,