866164 Mercruiser Fitting, Reducer(.75-14 x .125-27)


866164 Fitting, Reducer(.75-14 x .125-27) Mercruiser 4S42028TS, 4S42028TT Fitting
866164 Fitting, Reducer(.75-14 x .125-27) Mercruiser
Rating:
73

Buy Fitting, Reducer(.75-14 x .125-27) 866164 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

4S42028TS   4S42028TT   Mercruiser

Mercruiser entire parts catalog list:

4S42028TS 1998
4S42028TT 1998

Information:

1. Remove shaft (2). Remove pin (1) from the shaft.2. Remove pins (3) from the flyweights. Remove flyweights (4). 3. Remove ring (7), races (8) and bearing (6) from riser (follower) (5).
Cover (7) holds spring (10) under compression.
4. Remove cover (9) and spring (10) from the governor housing.5. Remove lip type seal (11) from cover (9).6. Remove cover (12) for the low and high idle adjustments. 7. Remove locknut and screw (15) for the high idle adjustment.8. Remove bolt (17) and the washer for the low idle adjustment.9. Remove spring (18) and the guide.10. Remove pin (16) and plate (13).11. Remove shaft (14) from the housing. 12. Remove two spacers (19) and pin (20) from the shaft. 13. Remove shaft (21) from the governor housing.14. Remove washer (22) and levers (23) and (24) from the governor housing. 15. Remove lip type seal (25) and the bearing from the governor housing.16. Remove lip type seals (26) and (27) from the governor housing.Assemble Governor
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.end by:a) connection of governor to fuel injection pump housing


Parts fitting Mercruiser:

29085
 
29085 FITTING, OIL PRESSURE SENDER ADAPTOR
2165203, 2165208, 4231017L1, 4454110JT, 4454118JT, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 473B1F0GS, 474L111JS, 474L118JS, 474L118JT, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
74036
 
74036 FITTING, GREASE - GIMBAL HOUSING (STAINLESS STEEL)
00014332, 00019003, 01207333, 01321017, 01326013, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 2140208, 2165208, 2250507, 228801, 257B021JS, 260801, 30001854, 37011856, 40280002D, 40420001D, 40420002D, 40430002S, 40
88517
 
88517 FITTING, Reducing, TRANSMISSION ELBOW
02297343, 03307332, 03308333, 04544347, 30001854, 37011856, 40500006T, 40500010T, 40500010U, 40500120U, 44031854, 443B100JS, 4M4102LTS, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
42861 1
 
42861 1 FITTING, Pipe - Brass (.750-14)
00019003, 01321017, 01326013, 01701335, 40200002D, 40200002G, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 4
805059
FITTING
805059 FITTING
02602347, 02608427, 257B021JS, 40500120U, 4211015L1, 4231017L1, 4262C01JT, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 443B1003S, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 444106LPS, 44541101S, 4454110JT, 4454118JT,
862958
 
862958 FITTING, Oil Filter Adaptor
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
856594
 
856594 FITTING, Barbed
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
865417
 
865417 FITTING, Female Quick Connect
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE, 5111200LP, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900T
Back to top