810924 FLANGE ASSEMBLY (3.0L) Mercruiser
430B00001
FLANGE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$18.95
08-06-2024
0.44[0.20] pounds
US: Race-Driven Inc
Ball Joint fits Yamaha Bruin 350 YFM350 2x4 2004-2006 Upper x1 by Race-Driven
Race-Driven Race-Driven Upper Ball Joint || Ball Joints are designed to meet or exceed OEM specifications || Fits: 2004 2005 2006 Yamaha Bruin 350 YFM350BA
Race-Driven Race-Driven Upper Ball Joint || Ball Joints are designed to meet or exceed OEM specifications || Fits: 2004 2005 2006 Yamaha Bruin 350 YFM350BA
$49.59
08-06-2024
0.18[0.08] pounds
US: Powersport Superstor
Winderosa 810924 Top End Gasket Set
Winderosa Gasket Set Top End 810924 YAMAHA YFM250 08-10 || Made in the USA
Winderosa Gasket Set Top End 810924 YAMAHA YFM250 08-10 || Made in the USA
$39.26
07-10-2017
QUADBOSS: QUADBOSS
QUADBOSS 810924 QB FULL TOP END SET
Number on catalog scheme: 24
Compatible models:
430B00001
Mercruiser
Mercruiser entire parts catalog list:
Information:
1. Remove bolt (1), six bolts (2), two top bolts (3), housing (4) and the gasket. 2. Remove governor spring (5), the two wave washers, one flat washer and seat from the guide in the housing. 3. Remove bolts (6), cover (7) and the gasket from the housing. Use tooling (A) to remove seal (8) from the cover. 4. Remove low idle adjustment screw (9) and spring (10) from the housing. 5. Remove shaft assembly (12), lever (11) and lever (13) from the housing. 6. Remove two snap rings from pins (15) and remove pins (15). Remove plates (14) and stop (16) from the shaft assembly. 7. Remove pin (18), pin (17) and spring (19) from the shaft assembly. 8. Remove shaft (20) and lever (21) from the housing.
Remove check valve (22) only if a replacement is necessary because the check valve will be damaged during removal.
9. Remove check valve (22) if a replacement is necessary. 10. Remove contact (23) and body (24) for the governor dashpot adjustment screw from the housing.11. Remove bolts (25), cover (26) and the gasket from the housing. 12. Remove seal (27) and adjustment screw (28) for the high idle. 13. Remove two bolts (29), housing (30) and the gasket from the fuel injection pump housing. 14. Remove bolts (31) and torque control group (32).15. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 16. Remove bolts (34) and block (33) for the full load stop from the housing. 17. Remove the bolt that holds collar (35) to bolt (37). Remove collar (35) and spring (36) from bolt (37). Remove bolt (37) from the block.18. Remove the stop screw from collar (35) if a replacement is necessary. 19. Remove bolts (39) and governor servo (38) from the fuel injection pump. 20. Remove lockring (44), seat (43), spring
Remove check valve (22) only if a replacement is necessary because the check valve will be damaged during removal.
9. Remove check valve (22) if a replacement is necessary. 10. Remove contact (23) and body (24) for the governor dashpot adjustment screw from the housing.11. Remove bolts (25), cover (26) and the gasket from the housing. 12. Remove seal (27) and adjustment screw (28) for the high idle. 13. Remove two bolts (29), housing (30) and the gasket from the fuel injection pump housing. 14. Remove bolts (31) and torque control group (32).15. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 16. Remove bolts (34) and block (33) for the full load stop from the housing. 17. Remove the bolt that holds collar (35) to bolt (37). Remove collar (35) and spring (36) from bolt (37). Remove bolt (37) from the block.18. Remove the stop screw from collar (35) if a replacement is necessary. 19. Remove bolts (39) and governor servo (38) from the fuel injection pump. 20. Remove lockring (44), seat (43), spring