811982 Mercruiser OUTPUT FLANGE


811982 OUTPUT FLANGE Mercruiser 428B116KD, 442B110GD, 442B115KD, 4A72040ND OUTPUT
811982 OUTPUT FLANGE Mercruiser
Rating:
83

Buy OUTPUT FLANGE 811982 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$34.99

24-11-2024

US: Off Brand Parts Dire
Ignition Switch (E-Ton Vector 250) 4 Pins in 4 Pin Female Jack
OBPD Common applications include: E-Ton Vector 250, VXL-250 (Vin: LRA)
$150.00

24-11-2024
1.2[0.54] Pounds
US: EWS MotorSports LLC
Vertex Gasket Set With Oil Seals (811982) for Can-Am Maverick MAX 1000 XMR 17, Maverick MAX 1000 XRS 14-15, Renegade 1000, Renegade 1000 XMR, Renegade 1000 XXC 16-17, Maverick MAX 1000 TURBO 16-17
Winderosa Includes every gasket O-ring and seal required to rebuild an engine. || Includes formed rubber valve cover gaskets. || Does not include mechanical water pump seal.
$188.22

24-11-2024

US: EWS MotorSports LLC
Vertex 811982 Gasket Set with Oil Seals
Winderosa New
Number on catalog scheme: 59
 

Compatible models:

Mercruiser entire parts catalog list:

Information:

1. Remove the plug from location (1). Install Tool (A) in the hole with the square end down. Move the governor control to the "ON" position until the rack stops against Tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Remove washers (3). Put caps on all fuel openings.3. Remove bushing (4) with Tool (B).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
4. Remove fuel injection pump with Tool (C).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
5. Disassemble the fuel injection pump. Remove ring (6). Make a separation of bonnet (5) from the plunger and barrel assembly (7).
Do not remove the gear from the plunger. The gear and plunger are assembled and adjusted at the factory.
6. Remove the plunger and gear segment, washer and spring from the barrel.7. Remove the ring, spring, collar and valve from the barrel. 8. Remove spacer (8) from the pump bore.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (10), washer (5) and spring (9) in position on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4). 4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use Tool (C) to install the pump. 5. Install the seal and bushing (15) in the pump housing bore. If the pump is in the correct position, bushing (15) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (15) to a torque of 205 14 Nm (150 10 lb ft) with Tool (B).6. Install washers (16).7. Connect the fuel lines to the injection pumps and tighten fuel line nuts to a torque of 40 7 Nm (30 5 lb ft) with Tool (D).8. Check for correct installation of the injection pumps with the engine stopped. See the topic "Installation of Injection Pump" in the Systems Operation Testing & Adjusting Manual.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
9. Remove the timing pin [Tool (A)] and install the plug in the injection pump housing.


Parts output Mercruiser:

813330
 
813330 OUTPUT FLANGE
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813340
 
813340 OUTPUT SHAFT
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813343
 
813343 OUTPUT SHAFT
428B116KD, 442B110GD, 442B115KD, 4A72040ND
813346
 
813346 OUTPUT SHAFT
428B116KD, 442B110GD, 442B115KD, 4A72040ND
811980
 
811980 OUTPUT SHAFT
428B116KD, 442B110GD, 442B115KD, 4A72040ND
Back to top