8539 Mercruiser FLOAT BOWL KIT


8539 FLOAT BOWL KIT Mercruiser 02297343, 02602347, 02608427, 07711346 FLOAT
8539 FLOAT BOWL KIT Mercruiser
Rating:
43

Buy FLOAT BOWL KIT 8539 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

Mercruiser entire parts catalog list:

02297343 1983,1985,1986
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
07711346 1986,1987

Information:


Table 1
CDL Code and Description Comments
4767-3
Engine Fuel #2 Tank #1 Level Sensor : Voltage Above Normal The signal from the level sensor indicates that the value has exceeded the upper working range of the sensor.
The code is logged.
4767-4
Engine Fuel #2 Tank #1 Level Sensor : Voltage Below Normal The signal from the level sensor indicates that the value has exceeded the upper working range of the sensor.
The code is logged.
4767-8
Engine Fuel #2 Tank #1 Level Sensor : Abnormal Frequency, Pulse Width, or Period The signal from the level sensor is valid but not operating in the correct frequency range that the sensor would normally output.
The code is logged.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active or logged.
Proceed to Test Step 2.
Result: A -4 code is active or logged.
Proceed to Test Step 3.
Result: A -8 code is active or logged.
Proceed to Test Step 5.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Pin B (sensor return) and Pin C (sensor signal)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Turn the keyswitch to the OFF position.
Create a Short
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -4 code did not become active.
Proceed to Test Step 4.
3. Create an Open at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
E. Turn the keyswitch to the OFF position.
Create an Open
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -3 code did not become active.
Proceed to Test Step 4.
4. Check the 24 VDC Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the ON position.
B. Measure the voltage at the following pin locations of the affected sensor connector:
- Pin A and Pin B
C. Reconnect the sensor.
Supply Voltage
Result: The supply voltage is approximately 24.0 0.2 VDC
Proceed to Test Step 8.
Result: The supply voltage is not approximately 24.0 0.2 VDC.
Repair: There is a short in the wiring harness to ground or an open circuit. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 5.
5. Check the PWM Circuit for an Open
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector at the ECM.
D. Measure the resistance between the following locations for the sensor:
- Pin C (sensor connector) and the appropriate PWM signal wire on the ECM connector
Open Circuit
Result: Less than 10 ohms of resistance between the sensor connector and the ECM connector.
Proceed to Test Step 6.
Result: More than 10 ohms of resistance between the sensor connector and the ECM connector.
Repair: There is an open circuit in the wiring harness. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 6.
6. Check the PWM Circuit for a Short Circuit
A. Turn the keyswitch to the OFF position
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector at the ECM.
D. Measure the resistance between the following locations for the sensor:
- Pin C (sensor connector) and Engine ground
Short Circuit
Result: There were more than 100 K ohms of resistance between pin C and engine ground.
Proceed to Test Step 7.
Result: There were less than 100 K ohms of resistance between pin C and engine ground.
Repair: There is a short circuit in the wiring harness. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 7.
7. Check the PWM Circuit for a Pin to Pin Short Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector at the ECM.
D. Measure the resistance between the following locations for the sensor:
- Pin C (sensor connector) and all ECM connector pins
Short Circuit
Result: There were more than 100 K ohms of resistance between the signal pin at the ECM and all other pins in the ECM connector.
Proceed to Test Step 8.
Result: There were less than 100 K ohms of resistance between the signal pin at the ECM and all other pins in the ECM connector.
Repair: There is a short circuit in the wiring harness. Repair or replace the wiring harness
If the problem is not resolved, proceed to Test Step 8.
8. Perform the Wiggle Test
Carefully following this procedure is the best way to identify the root cause of an intermittent problem.
A. Turn the keyswitch to the ON position.
B. Connect Cat ET.
C. Use CAT ET to perform the following test:
- "Wiggle Test"
D. Slowly wiggle the wiring and the connectors between the P2 connector and the sensor. Pay particular attention to the wiring near each connector. Be sure to wiggle all the wiring. As you wiggle the wiring look for the following problems:
- Loose connectors or damaged connectors
- Moisture on the connectors or the wiring
- Damaged that is caused by excessive heat
- Damage that is caused by chafing
- Improper routing of wiring
- Damaged insulation
Test
Result: The wiring failed the Wiggle Test.
Repair: There is a problem with the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: The wiring passed the Wiggle Test.
The problem may be intermittent. Inspect the wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect" for additional information.
Repair: Perform the following procedure:
1. Turn the keyswitch to the OFF position.
2. Disconnect the connectors. Carefully inspect the terminals for proper installation.
3. Insert a pin into each socket. Verify that each socket grips the pin firmly. Repair any problems.
4. Connect all connectors.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC


Parts float Mercruiser:

8753
 
8753 FLOAT BOWL KIT
00014332, 02287333, 02602347, 02607333, 02608427, 08987343, 260801
8546
 
8546 FLOAT KIT
00014332, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03307332, 03308333, 04544347, 06661346, 07711346, 08987343, 228801, 260801, 474H110AR
8750
 
8750 FLOAT BOWL KIT
00014332, 02287333, 02602347, 02607333, 02608427, 08987343, 228801
9031
 
9031 FLOAT
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01854335, 02287333, 02602347, 02607333, 02608427, 04707333, 04708004, 08987343, 257B021JS, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 4211015L1, 4211025RS, 4211025TS, 4211025TT,
8763
 
8763 FLOAT BOWL KIT
00014332, 02287333, 02607333, 02608427, 08986342, 08987343
8768
 
8768 FLOAT KIT
00014332, 02287333, 02607333, 02608427, 08986342, 08987343
8575
811536
FLOAT KIT (ALL)
811536 FLOAT KIT (ALL)
02602347, 02608427, 257B021JS, 4350100KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 44541101S, 4454110GE, 4454110JT, 45021102S, 457B100KS
Back to top