805723 Mercruiser GASKET

(1) Torque for fuel injection line nut ... 40 7 N m (30 5 lb ft)(2) Torque for retainer ... 48 7 N m (35 5 lb ft)(3) Torque for bleed screw ... 2.2 0.8 N m (20 7 lb in) Always use a new washer (seal) anytime the bleed screw is loosened or removed.(4) Washer. Make sure the correct washer is used when the nozzle assembly is installed. Check the Engine Arrangement for the correct part number to use.(5) Put liquid soap on rubber O-ring and bore in head before assembly.(6) Put 5P3931 Anti-Seize Compound on the threads of the adapter before installation. Torque for the adapter ... 205 14 N m (150 10 lb ft)See Testing And Adjusting section, for fuel injection nozzle test procedure.Earlier Engines
(1) Nut for fuel line. Hold adapter assembly (2) when nut (1) is loosened or tightened. Torque for the nut ... 40 7 N m (30 5 lb ft)(2) Adapter assembly.(3) Torque for bleed screw ... 1.6 0.4 N m (14 4 lb in)Always use a new washer (seal) anytime the bleed screw is loosened or removed.(4) Washer. Make sure the correct washer is used when the nozzle assembly is installed. Check the Engine Arrangement for the correct part number to use.(5) Torque for clamp bolt ... 31 7 N m (23 5 lb ft)(6) Put liquid soap on rubber O-ring and bore in head before assembly.(7) Put 5P3931 Anti-Seize Compound on the threads of the adapter before installation. Torque for the adapter ... 205 14 N m (150 10 lb ft)Engines With Capsule-Type Nozzles
Earlier Engines
(1) Torque for the nuts that hold the fuel injection lines to the nozzles ... 40 7 N m (30 5 lb ft)(2) Torque for nuts that hold the nozzles ... 75 7 N m (55 5 lb ft)(3) Body.(4) Nozzle. Tighten nozzle finger tight on body (3).(5) Put liquid soap in the bore in the cylinder head and on the O-ring seal. Put 5P3931 Anti-Seize Compound on the threads before installation. Torque for earlier direct injection adapter ... 205 14 N m (150 10 lb ft)Later Engines
(1) Torque for the nuts that hold the fuel injection lines to the nozzles ... 40 7 N m (30 5 lb ft)(2) Bolt. Tighten the four clamp bolts as follows: Tighten the bolts for the first clamp to a torque of ... 31 7 N m (23 5 lb ft)Tighten the bolts for the other clamp to a torque of ... 31 7 N m (23 5 lb ft)Again tighten the bolts for the first clamp to a torque of ... 31 7 N m (23 5 lb ft)(3) Clamp.(4) Sleeve.(5) Body.(6) Nozzle. Tighten nozzle finger tight on body (3).(7) Put liquid soap in the bore in the cylinder head and on the O-ring seal. Put 5P3931 Anti-Seize Compound on the threads before installation. Torque for later direct injection adapter ... 135 7 N m (100 10 lb ft)Precombustion Chamber Engines
(1) Torque for the nuts that hold the fuel injection lines to the nozzles ... 40 7 N m (30 5 lb ft)(2) Torque for nuts that hold the nozzles ... 75 7 N m (55 5 lb ft)(3) Body.(4) Nozzle. Tighten nozzle finger tight on body (3).(5) Put liquid soap in the bore in the cylinder head and on the O-ring seal. Put 5P3931 Anti-Seize Compound on the threads before installation. Torque for precombustion chamber ... 205 14 N m (150 10 lb ft)(6) Torque for glow plug ... 13.6 2.7 N m (120 24 lb in)