805799 Mercruiser GASKET


805799 GASKET Mercruiser 473B1F0GS GASKET
805799 GASKET Mercruiser
Rating:
98

Buy GASKET 805799 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

473B1F0GS   Mercruiser

Mercruiser entire parts catalog list:

Information:

Start By:a. remove flywheel 1. Put holes (2) evenly around seal (1) with a sharp punch as shown. Remove seal (1) and Tool (A). When a replacement of the earlier type rear seal is made, a replacement of the wear sleeve is to be made also. Later type seals and wear sleeves come as a set and must be replaced as a set. 2. Install Tool (C) in the rear seal bore.3. Install Tool (B) between the wear sleeve. Turn Tool (B) until the edge of the tool makes a flat plate (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove Tool (C) and the wear sleeve by hand.Install Crankshaft Rear Seal & Wear Sleeve
1. Install earlier crankshaft rear seals and wear sleeves with Tool (A) or later crankshaft sleeves with Tool (A) or later crankshaft rear seals and wear sleeves with Tool (B) as follows:a. Install locator (2) and the bolts on the rear of the crankshaft.b. Clean and prepare the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Apply 9S3265 Retainer Compound to the crankshaft outside diameter and wear sleeve inside diameter before wear sleeve is installed on the crankshaft.c. For earlier type seals, put clean engine oil on the seal lip of the seal and on the outside diameter on wear sleeve. Make sure the lip of the seal is toward the inside of the engine and the outside diameter bevel of wear sleeve is toward the outside of the engine. Later type seals and wear sleeves cannot be used again after the seals are separated.d. Put the wear sleeve and seal in position on locator (2) as a unit.
On later type seals, make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
On later type seals, the front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
e. Put the correct installer (4) in position on locator (2).f. Put clean engine oil on the face of nut (3) and its contact area on installer (4). Install nut (3) on locator (2).g. Tighten nut (3) until the inside surface of installer (4) comes in contact with locator (2).
On some early engines with lip-type seals, if the seals goes against the bottom of the bore, a resistance (increase in torque) will be felt on nut (3). Do not tighten nut (3) too tight or the case (body) of the seal will be damaged.
h. Remove Tool (A) or (B). For more information on the crankshaft seal installation, see Special Instruction, Form No. SMHS7100 (for earlier lip-type seals), and SMHS8508 (for later seal groups with hydrodynamic grooves).End By:a. install flywheel


Parts gasket Mercruiser:

7013
 
7013 GASKET, VOLTAGE REGULATOR TO ALTERNATOR
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
71614
 
71614 GASKET, PRESSURE CAP
01701335, 02287333, 02297343, 02607333, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04856332, 04881333, 08986342, 228801, 260801, 40420001D, 428B116KD, 442B110GD, 442B115KD, 473B116KD, 473B1F0GS, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ20
805844
 
805844 GASKET
473B1F0GS
808188
 
808188 GASKET SET
473B1F0GS
808127
 
808127 GASKET
473B1F0GS
808260
 
808260 GASKET
473B1F0GS
805841
805842
GASKET
805842 GASKET
473B116KD, 473B1F0GS
Back to top