850476 Mercruiser GASKET SET


850476 GASKET SET Mercruiser 4454110JT GASKET
850476 GASKET SET Mercruiser
Rating:
83

Buy GASKET SET 850476 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$5.28
 

04-07-2022

-: -
Daiwa 850476 Basas Worm Hook SS / EWOS #1/0
Bassers Worm Hook SS EWOS (Extra Wide Offset) Wide type offset hook that matches the bulky worm. The width of the gape matches a wide variety of thick worms and larger worms such as swimbaits. Even with a slight bite, the tip can be easily popped out and securely hooked up
Number on catalog scheme: 6
 

Compatible models:

4454110JT   Mercruiser

Mercruiser entire parts catalog list:

4454110JT 1996,1997

Information:


Illustration 1 g00993011
Typical example
(1) Oil seal (2) Ring assembly (3) Ceramic ring and rubber seal (4) Seal assembly (5) Spring Follow these recommendations for installation of the seals:Note: The seal installation tool is part of the replacement seal assembly.
Install ring assembly (2) and oil seal (1) into the pump housing. Install the oil seal dry. Do not lubricate the sealing lip. Use the correct installation tool and use a slow, even motion to press the seal into the pump housing.
Install shaft (6) through the oil seal.
Install the shaft's thrust washer (7).
Lubricate the outside diameter of the ceramic ring and rubber seal (3) with clean water.
Orient the polished face of the ceramic ring toward seal assembly (4). Use the installation tool and hand pressure to seat the ceramic ring and the rubber seal into the pump housing.
Remove spring (5) from the seal assembly. Lubricate the inside diameter of the seal assembly with clean water.
Use the seal installation tool and hand pressure to install the seal assembly onto the shaft until the face of the seal assembly makes light contact with the face of the ceramic ring and rubber seal.
Install the spring onto the seal assembly. (6) Shaft Width of shaft's groove for thrust washer ... 8.75 0.05 mm (0.345 0.002 inch) (7) Thrust washer Thickness ... 8.50 0.05 mm (0.3346 0.0020 inch) (8) Nut Torque ... 200 25 N m (150 18 lb ft) (9) Stud Torque ... 35 5 N m (26 4 lb ft) (10) Nut Torque ... 27 4 N m (20 3 lb ft) (11) O-ring seal Lubricate the O-ring seal with clean engine oil. (12) O-ring seal Lubricate the O-ring seal with clean engine coolant. (13) O-ring seal Lubricate the O-ring seal with glycerin. (14) Adapter Torque ... 100 10 N m (75 7 lb ft)Maximum leakage per minute for the water seal at 138 kPa (20 psi) of air pressure ... 20 cc (1.22 cu in)Maximum leakage per minute for the oil seal at 138 kPa (20 psi) of air pressure ... 24 cc (1.46 cu in)Type 2
Illustration 2 g01026565
Typical example
(1) Oil seal (2) Ring assembly (3) Ceramic ring and rubber seal (4) Seal assembly (5) Spring (6) Shaft Shaft's outer diameter for impeller ... 25.400 0.013 mm (1.0000 0.0005 inch)Width of shaft's groove for thrust washer ... 8.75 0.05 mm (0.345 0.002 inch) (7) Thrust washer Thickness ... 8.50 0.05 mm (0.3346 0.0020 inch) (8) Impeller Diameter of impeller's bore ... 25.342 0.013 mm (0.9977 0.0005 inch) (9) O-ring seal (10) O-ring seal (11) Stud Torque ... 35 5 N m (26 4 lb ft) (12) Nut Torque ... 27 4 N m (20 3 lb ft) (13) O-ring seal (14) Adapter Torque ... 100 10 N m (75 7 lb ft)Assembly Procedure
Follow this procedure for assembly:Note: The seal installation tool is part of the replacement seal assembly.
Install ring assembly (2) and oil seal (1) into the pump housing. Install the oil seal dry. Do not lubricate the sealing lip. Use the correct installation tool and use a slow, even motion to press the seal into the pump housing.
Install shaft (6) through the oil seal and through the ring assembly.
Install thrust washer (7).
Lubricate the outside diameter of the ceramic ring and rubber seal (3) with clean water or with 207-1600 Rubber Lubricant.
Orient the polished face of the ceramic ring toward seal assembly (4). Use the installation tool and hand pressure to seat the ceramic ring and the rubber seal into the pump housing.
Remove spring (5) from the seal assembly. Lubricate the inside diameter of the seal assembly with clean water or with 207-1600 Rubber Lubricant.
Use the seal installation tool and hand pressure to install the seal assembly onto the shaft until the face of the seal assembly makes light contact with the face of the ceramic ring and rubber seal.
Install the spring onto the seal assembly.
Lubricate the shaft with clean engine oil. Place the shaft onto a fixture that will absorb the load and press impeller (8) onto the shaft until the face of the impeller is flush with the face of the shaft.
Lubricate the bore for O-ring seal (9) with clean engine oil.
Lubricate the bore for O-ring seal (10) with clean engine coolant.
Tighten studs (11) according to the specified torque.
Tighten nuts (12) according to the specified torque.
Lubricate the bore for O-ring seal (13) with glycerin.
Tighten adapter (14) according to the specified torque. Maximum leakage per minute for the water seal at 138 kPa (20 psi) of air pressure ... 20 cc (1.22 cu in)Maximum leakage per minute for the oil seal at 138 kPa (20 psi) of air pressure ... 24 cc (1.46 cu in)


Parts gasket Mercruiser:

49955
 
49955 GASKET, OIL PAN DRAIN SCREW
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 03302336, 03307332, 04544347, 06661346, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 257B021JS, 260
91892
 
91892 GASKET, ADAPTER COVER
01701335, 02297343, 02602347, 02608427, 03307332, 03308333, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 257B021JS, 30001854, 32001876, 37011856, 40500006T, 40500010T, 40500010U, 40500120U, 4052110CR, 4111021L1, 4111021TS, 4111021UT, 4
41609
 
41609 GASKET, CARBURETOR
44031854, 44541101S, 4454110GE, 4454110JT
41610
 
41610 GASKET, SPACER
02602347, 02608427, 4350104JS, 4350104KS, 44031854, 4441027LE, 444106AM1, 444106LPS, 44541101S, 4454110GE, 4454110JT, 45021102S, 4R42027N1
809077
 
809077 GASKET (ALL)
02602347, 02608427, 257B021JS, 4211015L1, 4350100KS, 443B1003S, 443B100JS, 443HC00JT, 44541101S, 4454110GE, 4454110JT, 45021102S, 457B100KS
811566
GASKET
811566 GASKET
44541101S, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474L111JS, 474L118JS, 474L118JT
850470A96
850465A96
Back to top