898101484 Mercruiser GASKET


898101484 GASKET Mercruiser 40280002D, 40420002D GASKET
898101484 GASKET Mercruiser
Rating:
18

Buy GASKET 898101484 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

40280002D   40420002D   Mercruiser

Mercruiser entire parts catalog list:

40280002D 1998
40420002D 1998

Information:


Table 1
Associated Codes
E198 Low Fuel Pressure
E390 Fuel Filter Is Restricted
5580-18 Engine Filtered Fuel Delivery Absolute Pressure : Low - moderate severity (2)
5584-15 Engine Fuel Filter Degradation : High - least severe (1) Note: If the engine will not start and Cat ET will not communicate with the ECM, the problem is most likely with the electrical power supply to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".
Table 2
Troubleshooting Test Steps Values Results
1. Inspection of the Fuel Supply
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
Fuel level
Result : The fuel level is OK.
Proceed to Test Step 2.
Result : The fuel level is NOT OK.
Repair : Fill the tank.
STOP
2. Check the Engine Shutdown Switches if Applicable
A. The engine shutdown switches must be in the OFF position.
B. Use Cat ET to verify the status of the engine shutdown switches. When a shutdown occurs, the keyswitch must be turned to the OFF position for at least 15 seconds before restarting the engine.
Engine shutdown switches
Result : The switches are in the OFF position.
Proceed to Test Step 3.
Result : The switches are not in the OFF position.
Repair : Turn the switches to the OFF position.
STOP
3. Check the Engine Starting Aids if Applicable
A. If cold ambient conditions exist, check the operation of the starting aids. Verify that the starting aid is operating correctly.
Starting aids
Result : The starting aid is operating correctly.
Proceed to Test Step 4.
Result : The starting aid is not operating correctly.
Repair : Refer to the appropriate circuit test in order to troubleshoot the starting aid.
4. Restrictions in the Air Inlet and Exhaust System
A. Check for an air filter restriction indicator.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Air and exhaust system restrictions
Result : There are no system restrictions.
Proceed to Test Step 5.
Result : There are system restrictions.
Refer to Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for more information on air system restrictions.
Repair : Replace plugged air filters. Refer to the Operation and Maintenance Manual for the correct procedure.
5. Check for Activation of the Theft Deterrent System if Applicable
A. Verify that the theft deterrent system is not active.
Theft deterrent system
Result : The theft deterrent system is not active.
Proceed to Test Step 6.
Result : The theft deterrent system is active.
Repair : Turn the theft deterrent system OFF.
6. Check the Coolant Temperature Sensor for Proper Operation
A. The coolant temperature sensor must provide a correct signal in order for cold mode operation to operate correctly.
Refer to Cold Mode Operation within the Systems Operation, "General Information".
B. Verify that the coolant temperature on Cat ET is reasonable for the conditions that are present.
Coolant temperature sensor
Result : The sensor is operating properly.
Proceed to Test Step 7.
Result : The sensor is not operating properly.
Repair : Refer to Troubleshooting, "Sensor Signal (Analog, Passive) - Test" for troubleshooting information.
7. Check the Engine Speed Signal for Proper Operation
A. Crank the engine and observe the engine speed on the Cat ET status screen. Refer to Troubleshooting, "Speed/Timing - Test" for additional information.
Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal.
Timing signal
Result : The timing sensor is operating properly.
Proceed to Test Step 8.
Result : The timing sensor is not operating properly.
Repair : Refer to Troubleshooting, "Speed/Timing - Test" for troubleshooting information.
8. Inspect the Low-Pressure Fuel System
A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
B. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
C. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
D. Check the filtered fuel pressure while the engine is being cranked. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the test procedure and for the correct pressure values.
If the fuel pressure is low, replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
E. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Low-pressure fuel system
Result : The low-pressure fuel system is not operating properly.
Repair : Make the necessary repairs. Return the engine to service.


Parts gasket Mercruiser:

854101
 
854101 GASKET
40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
854171
GASKET
854171 GASKET
40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
854214001
 
854214001 GASKET, Air Cooler
40280001D, 40280002D, 40420002D, 4C72040TD
854096001
 
854096001 GASKET, Front Cover
40280001D, 40280002D, 40420002D
879194122
 
879194122 GASKET
40280002D
898101476
 
898101476 GASKET, Wastegate
40280002D, 40420002D
879194154
Back to top