858331A 3 Mercruiser GEAR SET, (29/27)


858331A 3 GEAR SET, (29/27) Mercruiser 5232100N1, 5E31200N1, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6811001N1 GEAR
858331A 3 GEAR SET, (29/27) Mercruiser
Rating:
78

Buy GEAR SET, (29/27) 858331A 3 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Mercruiser entire parts catalog list:

5232100N1 1998
5E31200N1 1998
6211001N1 1998
6311002NZ 1998
6315001N1 1998
6315002NZ 1998
6416003N2 1998
6811001N1 1998

Information:

Start By:a. remove oil pumpb. remove oil pan plate 1. Remove No. 1, 3, 5 and 7 main bearing caps (1). Remove the lower halves of the main bearings from the main bearing caps.
If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area in the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
2. Install Tool (A) in the hole in the crankshaft journal, and turn the crankshaft to remove the upper halves of main bearings (2).3. Remove crankshaft thrust bearings (3) from the rear main bearing. Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in the cylinder block and the main bearing caps.
4. Use Tool (A), and install new upper halves of main bearings (2) in the cylinder block. Install new lower halves of main bearings (2) in main bearing caps (1).
When the bearing clearance is checked and the engine is in an upright position (vertical position with cylinder head on top), the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.
For complete details concerning measuring bearing clearances, see Engine Bearings & Crankshafts, SEBD0531.5. Check the main bearing clearance with Plastigage (B) as follows: a. Put a piece of Plastigage (B) on the crankshaft journals as shown.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
b. Put main bearing caps (1) in position in the engine. Put 4C-5593 Anti-Seize Compound on the bolt threads and the face of the washers, and install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb ft).c. Put a mark on each bolt and main bearing cap; then tighten the bolts 90 degrees (1/4 turn more).d. Remove the main bearing caps, and measure the Plastigage to find the bearing clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm (.0030 to .0065 in). Maximum permissible clearance with used bearings is 0.25 mm (.010 in). 6. Put clean oil on the thrust bearing, and install a new thrust bearing for the rear main bearing. Install the thrust bearing with the identification "BLOCK SIDE" toward the cylinder block and the tabs on the thrust bearings in the machined area in the cylinder block. Tabs (4) on thrust bearing (3) will not let the thrust bearing be installed backward. 7. Install main bearing caps (1), and tighten the bolts as in Steps 5b and 5c.8. Remove the remainder of the main bearing caps, and do Steps 2, 4, 5 and 7 again. 9. Check the crankshaft end play with Tooling (C). The end play is controlled by the thrust bearings on the rear main bearing. End play with new bearings must be 0.064 to 0.368 mm (.0025 to .0145 in). The maximum permissible end play with used bearings is 0.64 mm (.025 in).End By:a. install oil pan plateb. install oil pump


Parts gear Mercruiser:

8866A17
GEAR HOUSING ASSEMBLY (CASTING #1656-8865C2)
8866A17 GEAR HOUSING ASSEMBLY (CASTING #1656-8865C2)
5120136JS, 5120150AR, 5220200AS, 5231100LP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210TP, 5E36210T
8866A51
 
8866A51 GEAR HOUSING ASSEMBLY (2.43:1 Ratio)
5120136JS, 5120150R1, 5231100LP, 5232100N1, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
827303
GEAR, DRIVE (1.50:1 - 1.65:1 Ratio)
827303 GEAR, DRIVE (1.50:1 - 1.65:1 Ratio)
5120136JS, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
8866A63
GEAR HOUSING ASSEMBLY (Complete)
8866A63 GEAR HOUSING ASSEMBLY (Complete)
5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6811001N1
8866A64
GEAR HOUSING ASSEMBLY
8866A64 GEAR HOUSING ASSEMBLY
5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210T
8866G05
 
8866G05 GEAR HOUSING ASSEMBLY, (13/24) (Complete)
5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6811001N1
8866G08
GEAR HOUSING ASSEMBLY, Complete (18/25)
8866G08 GEAR HOUSING ASSEMBLY, Complete (18/25)
5231100TP, 5232100TP, 6311002NZ, 6315002NZ, 6811001N1
Back to top