41575A 1 Mercruiser HARNESS ASSEMBLY, SHIFT AND TRIM


41575A 1 HARNESS ASSEMBLY, SHIFT AND TRIM Mercruiser 00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08987343, 257B021JS, 457B100KS HARNESS
41575A 1 HARNESS ASSEMBLY, SHIFT AND TRIM Mercruiser
Rating:
83

Buy HARNESS ASSEMBLY, SHIFT AND TRIM 41575A 1 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Mercruiser entire parts catalog list:

Information:

The following conditions must exist before any of the above codes will become active:
There are no active 678 or 41 codes.
There are no active 168 codes.
Illustration 1 g06382099
Schematic diagram for the PWM sensors
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 and P1/J1 ECM connectors and the PWM sensors.
Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the sensors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check For Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the PWM sensors.
Repair: If there are logged diagnostic codes for the PWM sensors, the fault may be intermittent.
Refer to Troubleshooting, "Electrical Connectors - Inspect" to identify intermittent faults.
Result: A diagnostic code that is listed in Table 1 is active.
Proceed to Test Step 3.
3. Check the Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect sensor.
C. Turn the keyswitch to the ON position. Do not start the engine.
D. Measure the voltage between the supply terminal and the ground terminal on the harness connector for the suspect sensor. The voltage measurement should be battery voltage.
E. Turn the keyswitch to the OFF position.
F. Reconnect the sensor.
Between 7.5 V and 8.5 V for an 8 V supply
Between 11 V and 13 V for a 12 V supply
Between 22 V and 26 V for a 24 V supply
Result: The voltage measurement is not within the expected range. The fault is in the supply wire or the ground wire in the engine wiring harness.
Repair: Repair the faulty wiring or replace the faulty wiring.
Use the electronic service tool to clear all logged diagnostic codes. Return the engine to service.
Result: The voltage measurement is within the expected range - The correct supply voltage is reaching the sensor.
Proceed to Test Step 4.
4. Check the Type of Diagnostic Code that is Active
A. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
B. Use the electronic service tool to check for active diagnostic codes. Record all active diagnostic codes.
Diagnostic codes Result: A -8, or diagnostic code is active for one or more of the PWM sensors.
Repair: Replace the suspect sensor.
Use the electronic service tool


Parts harness Mercruiser:

70967
 
70967 HARNESS, DUMMY SENDER
00014332, 2140208, 2165208, 2250507
70968
 
70968 HARNESS, TRIM LIMIT SWITCH
00014332, 2140208, 2165208, 2250507
87394A20
 
87394A20 HARNESS ASSEMBLY, CONTROL PANEL
00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015
93542A 1
 
93542A 1 HARNESS ASSEMBLY, HYDRAULIC PUMP
00014332, 2140208, 2165208
74023A 1
 
74023A 1 HARNESS ASSEMBLY (USE WITHOUT FUSE)
00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015
805363A 2
 
805363A 2 HARNESS ASSEMBLY
02602347, 02608427, 45021102S
98423A14
 
98423A14 HARNESS ASSEMBLY
02602347, 02608427
98423A13
 
98423A13 HARNESS ASSEMBLY
02602347, 02608427
Back to top