862163T04 Mercruiser HARNESS ASSEMBLY, Wiring


862163T04 HARNESS ASSEMBLY, Wiring Mercruiser 4211025TS, 4211025TT, 4M11025TS, 4M11025TT HARNESS
862163T04 HARNESS ASSEMBLY, Wiring Mercruiser
Rating:
43

Buy HARNESS ASSEMBLY, Wiring 862163T04 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mercruiser entire parts catalog list:

4211025TS 1998
4211025TT 1998
4M11025TS 1998
4M11025TT 1998

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 2 g01131377
Illustration 3 g01158612
Valve bridge for dowel installations
Illustration 4 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
Valve bridge assemblies for dowel installations have an adjustment screw and a jam nut. Use the following procedure to install this configuration.
Loosen adjustment screw (11) and jam nut (12) on bridge assembly (3).
Coat these items with clean engine oil: the dowels, the receptacle of the bridge assembly for the dowels and the uppermost contact surface of bridge assembly (3).
Place bridge assembly (3) into position on the dowel. Apply a downward force of 5 to 45 N (1 to 10 lb) on the uppermost contact surface of bridge assembly (3). While you apply the force, turn adjustment screw (11) until the adjustment screw contacts the valve stem.
Turn the adjustment screw for an additional 20 to 30 degrees (1/3 to 1/2 of the hex).
Hold the adjustment screw in position and tighten jam nut (12) to a torque of 30 4 N m (22 3 lb ft).
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 4.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts evenly to a torque of 215 40 N m (160 30 lb ft).Note: The rocker shaft dowel must be located on the left-hand side of the rocker shaft when installed.
Illustration 5 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread, tighten to a torque of 120 15 N m (89 11 lb ft). If nut (10) is 1/2 inch thread, tighten to a torque of 70 15 N m (52 11lb ft).End By:
Install the valve mechanism cover.


Parts harness Mercruiser:

41575A10
 
41575A10 HARNESS ASSEMBLY
40430002S, 4211025RS, 4211025TS, 4211025TT, 424106LRS, 424106LTT
41575A11
 
41575A11 HARNESS ASSEMBLY, Extension
40430002S, 4211025RS, 4211025TS, 4211025TT, 424106LRS, 424106LTT, 444106LPS, 444236HRS, 4M11025RS, 4M11025TS, 4M4102LPS, 4M4102LRS, 4M4102LTS
865181A01
 
865181A01 HARNESS ASSEMBLY, Mercathode
4211025RS, 4211025TS, 4211025TT, 424106LRS, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M4102LRS, 4M4102LTS, 4S42028N1, 4S42028TS, 4S42028TT, 5111200LP, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210T
866785T01
 
866785T01 HARNESS ASSEMBLY, Extension
40500006T, 40500010T, 40500010U, 40500120U, 4M11025TT, 4M11025US
866784T01
 
866784T01 HARNESS ASSEMBLY, Extension
40500006T, 40500010T, 40500010U, 40500120U, 4M11025TT, 4M11025US
862575T04
 
862575T04 HARNESS ASSEMBLY, Wiring
4M11025TS, 4M11025TT
Back to top