879172155 Mercruiser HARNESS ASSEMBLY, Engine Assembly


879172155 HARNESS ASSEMBLY, Engine Assembly Mercruiser 424106LUS, 424106PUU HARNESS
879172155 HARNESS ASSEMBLY, Engine Assembly Mercruiser
Rating:
28

Buy HARNESS ASSEMBLY, Engine Assembly 879172155 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

424106LUS   424106PUU   Mercruiser

Mercruiser entire parts catalog list:

424106LUS 1998
424106PUU 1998

Information:


Illustration 1 g01436855
Schematic for the engine pressure sensors
Test Step 1. Inspect the Electrical Connectors and Wiring
Remove the electrical power from the ECM.
Illustration 2 g01199199
A typical left side view of the C9 engine
(1) Fuel pressure sensor
(2) Injection actuation pressure sensor
(3) Boost pressure sensor for the intake manifold
(4) Atmospheric pressure sensor
(5) Engine oil pressure sensor
(6) J2/P2 connectors
(7) ECM
(8) J1/P1 connectors
Illustration 3 g01255900
A typical left side view of the C7 engine
(9) Fuel pressure sensor
(10) Injection actuation pressure sensor
(11) Atmospheric pressure sensor
(12) Boost pressure sensor for the intake manifold
(13) Engine oil pressure sensor
(14) J2/P2 connectors
(15) ECM
(16) J1/P1 connectors
Thoroughly inspect connectors (6) and (8). Thoroughly inspect the connectors for each engine pressure sensor. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01209367
P2 ECM connector
(P2-15) Boost pressure sensor for the intake manifold
(P2-17) Sensor return
(P2-54) Sensor return
(P2-28) Engine oil pressure sensor
(P2-40) Fuel pressure sensor
(P2-57) Atmospheric pressure sensor
(P2-85) Injection actuation pressure sensor
(P2-72) +5 V Supply
(P2-80) +5 V Supply
Illustration 5 g01123211
Connectors for the sensors
(A) Supply
(B) Return
(C) Signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the engine pressure sensors.
Check the torque of the allen head screws for the ECM connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from each sensor back to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring and/or the connectors.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the problem is resolved.STOPTest Step 2. Check the Voltage on the +5 V Supply Wire
Remove the electrical power from the ECM.
Disconnect the harness connectors for the following sensors:
Injection actuation pressure sensor
Boost pressure sensor for the intake manifold
Atmospheric pressure sensor
Fuel pressure sensor
Engine oil pressure sensor
Restore the electrical power to the ECM.
Measure the voltage between terminals A (+5 VDC) and B (Return) at each sensor connector on the engine harness.
Remove the electrical power from the ECM.
Connect all of the sensors. Expected Result:Each voltage measurement is 5.0 0.2 VDC.Results:
OK - Each voltage measurement is 5.0 0.2 VDC. Proceed to Test Step 3.
Not OK - At least one voltage measurement is not 5.0 0.20 VDC.Repair: Refer to the diagnostic functional test Troubleshooting, "5 Volt Engine Pressure Sensor Supply Circuit - Test".STOPTest Step 3. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to electronic troubleshooting Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the ECM.
Observe the "Active Diagnostic" screen on Cat ET. Wait at least 30 seconds so that any codes may become active. Look for an active diagnostic code for an engine pressure sensor.
Determine if the problem is related to a 03 diagnostic code or a 04 diagnostic code. Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active for the engine pressure sensors.Repair: If any of the above codes are logged and the engine is not running properly, refer to troubleshooting without a diagnostic code Troubleshooting.If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Active 04 code - An 04 diagnostic code is active. Proceed to Test Step 4.
Active 03 code - An 03 diagnostic code is active. Proceed to Test Step 5.Test Step 4. Disconnect the Suspect Sensor in Order to Create an Open Circuit
Remove the electrical power from the ECM.
Disconnect the sensor connector of the sensor with the 04 diagnostic code.
Restore the electrical power to the ECM. Wait at least 30 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Code" screen on Cat ET. Check for an active 03 diagnostic cod


Parts harness Mercruiser:

865181T01
 
865181T01 HARNESS ASSEMBLY, Mercathode
40200002D, 40200002G, 40280002D, 40420002D, 40500006T, 40500010T, 40500010U, 40500120U, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 4C72040TD, 4M11025US, 4S42028UT, 4S42028UU, 4S420P8UE
865677T02
 
865677T02 HARNESS ASSEMBLY
40500010T, 40500010U, 40500120U, 41510P1UE, 424106LUS, 424106PUU
899719T05
HARNESS ASSEMBLY, Extension
899719T05 HARNESS ASSEMBLY, Extension
4211025US, 4211025UU, 424106LUS, 424106PUU
812733A 2
 
812733A 2 HARNESS ASSEMBLY, Extension (Lube Bottle)
424106LRS, 424106LTT, 424106LUS, 424106PUU, 444236HRS, 4M4102LRS
866332T01
Back to top