8M2013910 Mercruiser HARNESS/SWITCH ASSEMBLY, eStop


8M2013910 HARNESS/SWITCH ASSEMBLY, eStop Mercruiser 40200002D, 40200002G, 40280002D, 40420002D HARNESS
8M2013910 HARNESS/SWITCH ASSEMBLY, eStop Mercruiser
Rating:
43

Buy HARNESS/SWITCH ASSEMBLY, eStop 8M2013910 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

Mercruiser entire parts catalog list:

40200002D 1998
40200002G 1998
40280002D 1998
40420002D 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Cap Kit 1 Start By:
Remove the inlet air control (NRS Induction Mixer) and mounting bracket. Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Remove" for the correct procedure.
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g02178677
Thoroughly clean the area around fuel manifold (4).
Disconnect harness assembly (6) from fuel pressure sensor (5).
Disconnect plastic tube assembly (1) from the fuel pressure relief valve on fuel manifold (4). Immediately cap the open port in fuel manifold (4) with a new cap. Immediately plug the open end of plastic tube assembly (1) with a new plug.
Remove bolts (2) and bolts (3). Remove fuel injection line support bracket (7).
Remove fuel manifold (4) from cylinder head. Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage. Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines or the fuel pressure relief valve are installed.
Illustration 2 g02178677
Position fuel manifold (4) onto the cylinder head. Install bolts (3) to fuel manifold (4) finger tight.
Position fuel injection line support bracket (7) onto the fuel rail. Install remaining bolt (3). Install bolt (2) for injection line support bracket (7) finger tight.
Install a new set of seals and a new set of fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.
Tighten bolts (3) to a torque of 22 N m (195 lb in).
Tighten bolts (2) to a torque of 9 N m (80 lb in).
Remove the plug from plastic tube assembly (1). Connect plastic tube assembly (1) to the fuel pressure relief valve.
Connect harness assembly (6) to fuel pressure sensor (5).
Replace the filters for primary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Primary (Water Separator) Element - Replace" for the correct procedure.
Replace the filters for secondary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information. End By:
Install the mounting bracket and the inlet air control (NRS Induction Mixer). Refer to Disassembly and Assembly, "Inlet Air Control (NRS Induction Mixer) - Install" for the correct procedure.


Parts harness Mercruiser:

879148018
 
879148018 HARNESS ASSEMBLY
40200002D, 40200002G
898101665
 
898101665 HARNESS ASSEMBLY
40200002D, 40200002G
865181T01
 
865181T01 HARNESS ASSEMBLY, Mercathode
40200002D, 40200002G, 40280002D, 40420002D, 40500006T, 40500010T, 40500010U, 40500120U, 4211025US, 4211025UU, 424106LTT, 424106LUS, 424106PUU, 4C72040TD, 4M11025US, 4S42028UT, 4S42028UU, 4S420P8UE
899887T05
 
899887T05 HARNESS ASSEMBLY, Wiring, Non-DTS
40200002D, 40200002G, 40280002D, 40420002D
899887T06
 
899887T06 HARNESS ASSEMBLY, Wiring, Tee
40200002D, 40200002G, 40280002D, 40420002D
879312T49
 
879312T49 HARNESS ASSEMBLY, Non-DTS Helm, Single & Twin Engine
40200002D, 40200002G, 40280002D, 40420002D
879312T21
 
879312T21 HARNESS ASSEMBLY, Panel Mount Lanyard Adapter
40200002D, 40200002G, 40280002D, 40420002D
879312T04
 
879312T04 HARNESS ASSEMBLY, Helm, DTS Single Engine
40200002D, 40200002G, 40280002D, 40420002D
Back to top