42851 HOSE, COOLER TO DRIVE UNIT Mercruiser
01207333, 01402414, 01407333
HOSE
Price: query
Rating:
Mercruiser entire parts catalog list:
- EXHAUST MANIFOLD AND WATER SYSTEM (USE W-2 PIECE EXH. ELBOW) » 42851
- EXHAUST MANIFOLD AND WATER SYSTEM (USE W-1 PIECE EXH. ELBOW) » 42851
- EXHAUST MANIFOLD AND WATER SYSTEM (USE W-2 PIECE EXH. ELBOW) » 42851
- EXHAUST MANIFOLD AND WATER SYSTEM (USE W-1 PIECE EXH. ELBOW) » 42851
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Drain the secondary filter. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 1 g03389479
Typical example
Make temporary identification marks on plastic tube assemblies to show the correct position of the plastic tube assemblies.
Place a suitable container below the fuel filter base to catch any fuel that might be spilled.
Disconnect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) from the fuel filter base.
Use Tooling (A) to plug the plastic tube assemblies. Use Tooling (A) to cap the ports in the fuel filter base.
Illustration 2 g03389486
Typical example
Remove secondary filter (6) from canister (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Remove bolts (4) from fuel filter base (5). Remove the fuel filter base from the mounting bracket.Note: Do not disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 3 g03389486
Typical example
Ensure that fuel filter base (5) is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Position fuel filter base (5) on the mounting bracket. Install bolts (4). Tighten the bolts to a torque of 44 N m (32 lb ft).
If necessary, install a new fuel filter (6) to canister (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Illustration 4 g03389479
Typical example
Remove the plugs from the plastic tube assemblies. Remove the caps from the ports in the fuel filter base.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Serious damage to the engine will result if contaminated fuel enters the fuel system.
Connect plastic tube assembly (1), plastic tube assembly (2), and plastic tube assembly (3) to the fuel filter base.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
Parts hose Mercruiser:
52481
52481 HOSE, WATER DISTRIBUTION BLOCK TO END CAP/ CONNECTOR
01207333, 01402414, 01406002, 01407333, 2165203, 2165208, 430B00001
48659 4
48659 4 HOSE, EXHAUST
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 4454110AS, 457B100KS
66348
66348 HOSE, OUTLET - OIL COOLER TO HEAT EXCHANGER (26")
01206002, 01207333, 01326013, 01406002, 01407333
64909
64909 HOSE, INTAKE - OIL COOLER TO TRANSOM PLATE (22")
01206002, 01207333, 01326013, 01406002, 01407333
49533
49533 HOSE, RETURN - OIL COOLER TO HYDRAULIC PUMP (48")
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04856332
49528
42850 64
42850 64 HOSE, INLET (3/4" I.D.)
01207333, 01402414, 01407333, 01701335, 04707333, 04708004, 04881333, 4111021L1, 430B00001, 430L000JS, 4441027LE, 444106AM1, 4M31027LS
44107